 |
Index for
Section 5 |
|
 |
Alphabetical
listing for J |
|
 |
Bottom of
page |
|
Japanese(5)
NAME
Japanese, japanese - Introduction to Japanese language support
DESCRIPTION
There are two national standards that specify the Japanese character sets
used for information interchange. The JIS X0201 standard specifies a
single-byte character set that consists of Roman letters and Katakana
characters. The JIS X0208 standard specifies a primary set of Japanese
ideographic characters. The operating system supports both standards with
coded character sets (codesets), locales, device, and other kinds of system
files.
Codesets
There are several codesets available to support Japanese. The following
list describes both the codesets and the strings that represent the
codesets in the names of locales, codeset converters, or both:
DEC Kanji, deckanji
See deckanji(5) for more information about the DEC Kanji codeset.
ESC/P Kanji, escp
This codeset, which is similar to ISO 2022-JP, is handled by conversion
to Tru64 UNIX Japanese codesets.
Fujitsu JEF, JEF
This Fujitsu codeset is handled by conversion to Tru64 UNIX Japanese
codesets. See iconv_JEF(5) for more information.
Hitachi KEIS, KEIS
This Hitachi codeset is handled by conversion to Tru64 UNIX Japanese
codesets. See iconv_KEIS(5) for more information.
IBM Kanji System, ibmkanji
This IBM mainframe codeset is handled by conversion to Tru64 UNIX
Japanese codesets. See iconv_ibmkanji(5) for more information.
Japanese EUC (Extended UNIX Code), eucJP
The default Japanese codeset. See eucJP(5) for more information about
the Japanese EUC codeset.
Super DEC Kanji, sdeckanji
See sdeckanji(5) for more information about the Super DEC Kanji
codeset.
Shift JIS, SJIS
The Shift JIS encoding format is identical to the Microsoft code-page
(cp932) format used on PC systems. Therefore, you can use codeset
converters whose names contain SJIS to convert data to and from cp932
format.
See shiftjis(5) for more information about the Shift JIS codeset.
JIS KANJI (JIS7 or JIS8)
JIS KANJI characters can be either JIS7 (representing characters in 7-
bit bytes) or JIS8 (representing characters in 8-bit bytes). Depending
on the kana input value, the string that represents the JIS7 codeset in
a codeset converter name is either jis7, JIS7, or jiskanji7.
JIS KANJI codesets are supported only for conversion operations as
indicated by the following table. These codesets are not supported by
locales or for direct input and output.
_________________________________________________________
Codeset Codeset Conversion Terminal Code Conversion
_________________________________________________________
jis7 Yes Yes
jiskanji7 Yes No
jis8 No Yes
_________________________________________________________
See jiskanji(5) for more information about JIS KANJI codesets, stty(1)
for information about terminal code conversion, and iconv_intro(5) for
information about codeset conversion.
ISO 2022-JP, iso2022JP
The ISO 2022-JP codeset is supported only for codeset conversion. It is
not supported by locales, for terminal code conversion, or for direct
input and output.
See ISO-2022-JP(5) for more information about the ISO 2022-JP codeset.
Extended ISO 2022-JP, iso2022JPext
The ISO 2022-JPext codeset (which is an extended version of ISO 2022-
JP) is supported only for codeset conversion. It is not supported by
locales, for terminal code conversion, or for direct input and output.
See ISO-2022-JP(5) for more information about the Extended ISO 2022-JP
codeset.
UCS formats: UCS-2, UCS-4, and ucs4
These encoding formats are supported only through locales or codeset
converters, not for terminal code conversion or for direct input and
output.
See Unicode(5) for more information about UCS formats.
UTF-8
See Unicode(5) for more information about UTF-8.
Locales
The following list specifies Japanese locales for Japan and the codesets
they support:
ja_JP.deckanji, for DEC Kanji
ja_JP.eucJP, for Japanese EUC (the default Japanese locale)
ja_JP.sdeckanji, for Super DEC Kanji
ja_JP.SJIS, for Shift JIS
ja_JP.UTF-8, for UTF-8
The ja_JP.deckanji@ucs4 and ja_JP.SJIS@ucs4 locale variants exist for
applications that need to convert file data in deckanji and SJIS format to
UCS-4 process code to perform certain character-classification operations.
The ja_JP.UTF-8 locale also uses UCS-4 format for process code, but
supports file code that conforms to the Unicode and ISO 10646 standards.
You can use the locale command (see locale(1)) to display the names of
locales installed on your system. See i18n_intro(5) for information on
setting locale from the operating system command line.
In the Common Desktop Environment (CDE), you also need to set the session
language. To do this, use the Language menu that is accessed from the
Options button of the Login window.
Japanese-Specific Character Properties
The Japanese locales (including the @ucs4 variants) define the following
properties (or classes) for characters:
ascii Characters for which the isascii() function returns a nonzero
(TRUE) value
english English-language characters as defined by the System V Multi-
National Language Specification (MNLS)
gaiji User-defined and vendor-defined characters (UDCs and VDCs)
ideogram
Ideographic characters as defined by the System V Multi-National
Language Specification (MNLS)
jdigit Digit characters as defined by JIS X0208
jhankana
Katakana characters and the voiced, semivoiced, and prolonged sound
marks as defined by JIS X0201
jhira Hiragana characters as defined by JIS X0208
jisx0201
All printable characters as defined by JIS X0201
jisx0201r
All printable, right-hand side characters as defined by JIS X0201
jisx0208
All printable characters as defined by JIS X0208
jisx0212
All printable characters as defined by JIS X012
jkanji Kanji characters as defined by JIS X0208 and JIS X0212, the Kanji
iteration mark as defined in JIS X 0208, and the Han-numeral zero
as defined by JIS X0208
jkata Katakana characters as defined by JIS X0201 and JIS X0208; the
voiced, semivoiced, and prolonged sound marks as defined by JIS
X0208 and JIS X0201; the Katakana iteration marks as defined by JIS
X0208
jparen Kana bracket characters as defined by JIS X0201 and the parentheses
characters as defined by JIS X0208
jspace The space character as defined by JIS X0208
line Line-drawing characters as defined by JIS X0208
number Numbers as defined by the System V Multi-National Language
Specification (MNLS)
paren Parentheses and other paired symbols as defined by JIS X0201 and
JIS X0208
phonogram
Phonograms as defined by the System V Multi-National Language
Specification (MNLS)
special Special characters as defined by the System V Multi-National
Language Specification (MNLS)
udc User-defined characters
vdc Vendor-defined characters
These properties supplement the ones specified by the XSH standard. Refer
to locale(4), wctype(3), and iswctype(3) for general information about how
characters are assigned properties in locales and how applications test
characters for supplemental properties.
Keyboards, Servers, and Input Methods
The operating system supports the following Japanese keyboards:
LK411-AJ
A Japanese version of the LK411 keyboard. This model does not have
special keys for Japanese input methods.
LK411-AJ ESC
A Japanese version of the LK411 keyboard.
LK411-JJ
A Japanese version of the LK411 keyboard. This model provides UNIX
layout and special keys for Japanese input methods.
LK97W-AJ
A Japanese version of the LK97W keyboard. This model has special keys
for Japanese input methods.
PCXAJA-JJ
A Japanese version of the PC keyboard. This model has special keys for
Japanese input methods.
For the Motif environment, the operating system provides the dxjim input
server to support Japanese input methods. For a CDE session, this input
server is started automatically if your session language is set to Japanese
at login time. Refer to the dxjim(1X) reference page for more information
about this input server and how to start it from the command line.
There are two main mechanisms for entering Japanese characters:
· Kana input, for entering Kana characters
The Kana input mechanism is provided by the firmware of Japanese video
terminals (see the Japanese Terminals section).
· Input methods, for entering two-byte Kanji characters, Kana
characters, letters, and symbols defined in JIS X0208. Input methods
allow characters to be entered and converted to other characters. The
four input methods are as follows:
Romaji-to-Kanji
Kana-to-Kanji
Internal Code
JIS Ku-ten Code
In the Motif environment, you must load a Japanese key mapping table
(keymap) that is appropriate for your keyboard. See keyboard(5) for
information on loading a keymap.
All the Japanese keyboards and keymaps support locking-shift mode
switching. In other words, you can enter English characters in the Mode
Switch Off state and Kana characters in the Mode Switch On state. The keys
used to toggle the input mode differ according to whether you are using a
Japanese VT terminal or, in the Motif environment, the keymap that has been
loaded.
· For Japanese VT terminals, press the Compose key.
· In the Motif environment press the Compose, or Comp, key if there is
one. Otherwise, press the right Ctrl key. These keys are defaults and
can be changed by the user.
Japanese Terminals
The operating system supports the VT282-J, VT382-J, and VT383-J terminals
for Japanese.
Running Motif Applications
X or Motif applications require non-ASCII fonts to display Japanese
characters. This means that the font path must be set appropriately before
starting an application that displays Japanese characters. An application
can find Japanese fonts in either of the following directories:
· /usr/i18n/lib/X11/fonts/decwin/75dpi, for low resolution display
· /usr/i18n/lib/X11/fonts/decwin/100dpi, for high resolution display
For applications running under CDE, Japanese screen fonts are found as long
as they are installed on the system or made available through a remote font
server. In other environments, you may need to use the following command to
check the font path before running a Japanese application:
% xset q
If one of the directories in the preceding list is not in the font path,
the following example shows how to add the directory. You can substitute
100dp for 75dpi if you want high resolution display.
% xset +fp /usr/i18n/lib/X11/decwin/75dpi/
% xset fp rehash
Printers
The operating system supports the following Japanese printers. The
associated print filter is noted in parentheses following the printer name.
· Japanese dot-matrix printers
LA84-J (la84of)
LA86-J (la86of)
LA90-J (la90of)
LA280-J (la280of)
· Japanese graphic line printers
LA380-J (la380of)
· Japanese laser printers
LN03-J (ln03jaof)
LN05-J (ln05jaof)
· Japanese PostScript printers
LN82R (ln82rof)
PostScript fonts for Japanese printers are printer resident. To print
Japanese text on generic PostScript printers, you can customize a print
filter to convert Japanese bitmap fonts to PostScript font encoding. Refer
to wwpsof(8) for more information.
See i18n_printing(5) for a general discussion of printer support options.
SEE ALSO
Commands: asort(1), locale(1), lp(1), lpr(1), dxjim(1X), xset(1X), lpd(8),
lprsetup(8)
Files: printcap(4)
Others: code_page(5), deckanji(5), eucJP(5), i18n_intro(5),
i18n_printing(5), iconv_ibmkanji(5), iconv_intro(5), iconv_JEF(5),
iconv_KEIS(5), iso2022jp(5), jiskanji(5), keyboard(5), l10n_intro(5),
sdeckanji(5), shiftjis(5), Unicode(5)
Using International Software
|
Index for
Section 5 |
|
|
Alphabetical
listing for J |
|
 |
Top of
page |
|