OpenVMS VAXSHAD09_062 V6.2 SHADOWING ECO Summary
TITLE: OpenVMS VAXSHAD09_062 V6.2 SHADOWING ECO Summary
Modification Date: 08-DEC-00
Modification Type: Updated Kit: Supersedes VAXSHAD08_062
NOTE: An OpenVMS saveset or PCSI installation file is stored
on the Internet in a self-expanding compressed file.
For OpenVMS savesets, the name of the compressed saveset
file will be kit_name.a-dcx_vaxexe for OpenVMS VAX or
kit_name.a-dcx_axpexe for OpenVMS Alpha. Once the OpenVMS
saveset is copied to your system, expand the compressed
saveset by typing RUN kitname.dcx_vaxexe or kitname.dcx_alpexe.
For PCSI files, once the PCSI file is copied to your system,
rename the PCSI file to kitname-dcx_axpexe.pcsi, then it can
be expanded by typing RUN kitname-dcx_axpexe.pcsi. The resultant
file will be the PCSI installation file which can be used to install
the ECO.
Copyright (c) Compaq Computer Corporation 1998, 1999. All rights reserved.
OP/SYS: DIGITAL OpenVMS VAX
COMPONENT: SHADOWING
SHDRIVER.EXE
SHADOW_SERVER.EXE
SOURCE: Compaq Computer Corporation
ECO INFORMATION:
ECO Kit Name: VAXSHAD09_062
ECO Kits Superseded by This ECO Kit: VAXSHAD08_062
VAXSHAD07_062
VAXSHAD06_062
ECO Kit Approximate Size: 1908 Blocks
Kit Applies To: OpenVMS VAX V6.2
System/Cluster Reboot Necessary: Yes
Rolling Re-boot Supported: Yes
Installation Rating: 2 - To be installed on all systems running
the listed version of OpenVMS and
using the following feature:
SHADOWING
Kit Dependencies:
The following remedial kit MUST be installed BEFORE
installation of this kit:
VAXCLUSIO01_062
In order to receive all the corrections listed in this
kit, the following remedial kits should also be installed:
None
ECO KIT SUMMARY:
An ECO kit exists for SHADOWING on OpenVMS VAX V6.2. This kit
addresses the following problems:
Problems Addressed in VAXSHAD09_062:
o A SHADOWSET goes into MOUNTVERIFYTIMEOUT and cannot be
remounted.The process attempting the mount hangs.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The system can crash with a SHADDETINCON bugcheck.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Disabling a FibreChannel cascade connection results in a
system crash.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Disabling a FibreChannel cascade connection results in a
corruption of a shadowset member.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Users that had used bit 16 in SHADOW_SYS_DISK to eliminate
using the remote members for read requests would occasionally
not exclude reads from going to the remote members.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o A CPUSPINWAIT bug check can occur if the read of the SCB of a
shadow set member cannot pass the checksum test.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o An assisted copy operation (DCD), will not always be initiated
properly. During an assisted copy operation, if the source
member was dismounted or otherwise removed from the shadow
set,the connection to the controller would not clean up
correctly.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o A full copy operation that is interrupted by a mini merge may
not be completed correctly.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o When a copy operation, that had interrupted a merge operation
is terminating, if there are no members marked for merge the
system can crash with a SHADDETINCON bugcheck.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o A SHOW DEVICES command shows zero % merged status, even though
the shadow set status does not indicate that a merge is
required.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Use of bit 16 in SHADOW_SYS_DISK bias reads of the local
source shadow set member does not always work.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The system can crash with a SHADBOOTFAIL bugcheck.Following
is a crash dump extract:
** Bugcheck code = 000008CC: SHADBOOTFAIL, SHADOWING failed to
boot from system disk shadow set
** Current Process = NULL
** Current PSB ID = 00000001
** Image Name =
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The system crashes with an INVEXCPTN bugcheck at SYS$SHDRIVER+6D0DC
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The system crashes in XQP when an IO gets a SS$_DATACHECK
during a Shadowset copy operation
Images Affected: [SYS$LDR]SHDRIVER.EXE
o SHADDETINCON crashes in the SHD_LOCK SHLK$MERGE_SIGNAL
routine.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o An incomplete SDA displays for DSA devices.
Images Affected: [SYSEXE]SDA.EXE
o The system crashes with a SHADBOOTFAIL bugcheck when booting.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o There may be an inconsistent display of output of $ SHOW
DEVICE /SERVED if SET DEVICE /SERVED issued at the same time.
A system crash could occur if queues are updated while SHOW
DEVICE /SERVED code is traversing the queues at elevated IPL
and the update causes an access violation or pagefault.
Images Affected: [SYSEXE]]SHOW.EXE
o Enable shadowing of devices that report the same value for
MAXBLOCK, but different values for CYLINDER, TRACK, and/or
SECTOR.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Match master hangs until MVTIMEOUT expires.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The master member of a multi member shadowset, whose members
are all valid, SRC MBRS, can have a generation number that is
older then the other 2 members:
master mbr ($1$DGA2015:)
SDA> eval/time 009E8F02.FBFF8657
21-APR-2000 10:15:30.08
mbr1 ($1$DGA2016):
SDA> eval/time 009E8F02.FDF405D2
21-APR-2000 10:15:33.36
mbr2 ($1$DGA3013):
SDA> eval/time 009E8F02.FDF405D2
21-APR-2000 10:15:33.36
If an attempt is made to mount this set on a client node, the
client node can hang the set in 'mounted alloc' state and
OPCOM will report path switches occurring for mbrs $1$DGA2016
& $1$DGA3013.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o The system crashes with INVEXCEPTN when a write completes to a
multi-member shadow set. An attempt to return to the WLE
(write log entry) fails because one member of the shadow set
has been removed and there is no Write Log Table.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o A system can crash with a SHADDETICON bugcheck after removing
or adding a shadow set member.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o When a full copy operation is pending or in progress, the
removal of the master shadow set member may cause data
corruption. The conditions under which this can occur are:
1. A full merge is pending or in process on a two member
shadow set.
2. A third member is added to the shadow set.
3. There is a difference between the two SRC members
4. The master member is then removed from the shadow set
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Under certain circumstances, when a path to a device is lost
during a write operation, the SCB (system control block) can
contain a stale master member index value. This will cause
the system to crash with a SHADDETINCON bugcheck.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o A crash in SHLK$MERGE_SIGNAL can occur on a cluster node.
This can happen when a lock value block in MRGVAL becomes
invalid due to another cluster node, that holds MRGVAL lock,
either crashing or being shut down.
Images Affected: [SYS$LDR]SHDRIVER.EXE
o Increase the merge factor for shadowing from 1,000 to 10,000.
This change also displays the merge factor only during an
actual merge operation.
Images Affected: [SYSEXE]SHADOW_SERVER.EXE
PROBLEMS ADDRESSED IN VAXSHAD08_062 KIT:
o Functionality was added to enable customers to shadow devices
that report an identical number of "Total Blocks".
In the past, Sectors per track, Tracks per cylinder, and Total
cylinders had to be identical, but the requirement is no
longer needed.
For example:
$ SHOW DEVICES/FULL $84$DKC200:
Disk $84$DKC200: (CSG84), device type RZ74, is online,
mounted, file-oriented device, shareable, served to a cluster
via MSCP Server, error logging enabled.
Error count 1 Operations completed 28293
Owner process "" Owner UIC [SYSTEM]
Owner process ID 00000000 Dev Prot S:RWPL,O:RWPL,G:R,W
Reference count 137 Default buffer size 512
Total blocks 6976375 Sectors per track 91
Total cylinders 3067 Tracks per cylinder 25
$ SHOW DEVICES/FULL $84$MDA1200:
Disk $84$MDA1200: (CSG84), device type RAM Disk, is online,
allocated, deallocate on dismount, mounted, file-oriented
device, shareable, served to cluster via MSCP Server.
Error count 0 Operations completed 420
Owner process "username" Owner UIC [SYSTEM]
Owner process ID 4260041B Dev Prot S:RWPL,O:RWPL,G:R,W
Reference count 2 Default buffer size 512
Total blocks 6976375 Sectors per track 64
Total cylinders 3407 Tracks per cylinder 32
Allocation class 84
These two devices can be members of the same shadow set.
Device Device Error Volume Free Trans Mnt
Name Status Count Label Blocks Count Cnt
DSA8400: Mounted 0 CSG84_V71 56308 319 1
$84$DKC200:(CSG84) ShadowSetMember 0 (member of DSA8400:)
$84$MDA1200:(CSG84) ShadowCopying 0 (copy trgt DSA8400: 2% copied)
USERNAME_CSG84 ...
o Faster I/O subsystems, for example the HSZ50 and the HSZ70,
were taking longer to perform full merges than some older and
slower subsystems.
Changes were made to allow the System Manager to adjust
thresholds. Two new logicals were adjusted to vary the merge
multiplication factor used for a virtual unit, on a per node
basis.
The logicals used must be defined in the system table and
therefore should be defined on each node in the cluster. The
valid range for a threshold is 100 to 1000. Any value outside
of this range causes a factor to default to 200. This value
of 200 is displayed at the start of a shadow set merge, in the
'%SHADOW_SERVER-I-SSRVINIMRG' message, following the word
'Factor'.
CAUTION:
Increasing the values excessively may cause application
performance problems when merges are occurring. When setting
values, System Managers must balance the site specific
application needs with their merge requirements.
Since two logical names are evaluated every one thousand I/Os,
the factor can possibly be adjusted while a merge is in
progress.
The first logical name is:
SHAD$MERGE_DELAY_FACTOR_DSAnnnn
^^^^
||||
vvvv
This logical name is virtual unit specific, with 'nnnn'
representing the virtual unit number. This delay factor will
be applied to the virtual unit only. If any important disks
need to be merged with minimal disruption, values as high
as 1,000% (threshold = 10 times best time) may be defined. By
the same token, if a particular disk's merge operation is
interfering with application I/O, it can cause the disk to
delay more frequently by reducing the value as low as:
100 (threshold = 1 times the best time)
If the above logical is not defined, then the following
logical is evaluated:
SHAD$MERGE_DELAY_FACTOR
Like the virtual unit specific logical, this value will adjust
the threshold, but only for all shadow sets that do not have a
virtual unit specific logical defined.
o Additional tracing code was added to help diagnose why mini
merge operations were converted to full merge.
o If full merge operations are interrupted with a copy
operation, then write logging is enabled, which wastes cluster
write logging resources.
o If a VMScluster that has more than 96 nodes crashes, then
write logging is never used to recover the virtual unit. The
result is unnecessary full merge operations.
o If a shadow set exists on multiple nodes in a cluster and one
cluster member adds a device which cannot be accessed by
other nodes in the cluster, then those nodes will crash with
an INVEXCEPTN in the SHDriver within SHSB$MATCH_MASTER_SCB.
When calling SHSB$AVAILABLE_SHADOW_SET, the call to log an
error packet resulted in an overwritten register (R0) and then
a system crash occurred.
An example of a crash footprint is:
Crash Time: 28-OCT-1998 12:47:46.03
Bugcheck Type: INVEXCEPTN, Exception while above ASTDEL
Node: ATOZ (Clustered)
CPU Type: AlphaServer 8400 Model EV56/440
VMS Version: V6.2-1H3
Current Process: ATOZ_1
Current Image: DSA1111:[RUN]GEM.EXE
Failing PC: FFFFFFF8026E454
Failing PS: 34000000 00000804
Module: SYS$SHDRIVER
Offset: 0003E454
Boot Time: 25-OCT-1998 18:51:50.00
o A Virtual Unit can hang and then no further use of the virtual
unit is possible. If the System Dump Analyzer (SDA) is used
to examine the virtual unit, then a negative value will be
found in UCB$W_RWAITCNT.
o Repeating mini merges or full merges can occur immediately
after the successful completion of a previous mini merge or
full merge on a virtual unit.
o During a system shutdown, two possible scenarios could occur:
1. Other nodes that have the system disk virtual unit MOUNTed
may suspend use of that virtual unit, until the node
running shutdown is stopped.
2. When a system disk that is disabled for write logging is
mounted on several nodes in a cluster, a non-system disk
volume aCCESS qto that virtual unit in the cluster may
suspend, until the node running shutdown is stopped.
o During a system reboot, the rebooting node may intermittently
hang if write logging is concurrently enabled on the system
disk and on other nodes in the cluster.
o Since a virtual unit can be aborted for several reasons,
additional tracing is needed to differentiate why the virtual
units abort.
PROBLEMS ADDRESSED IN VAXSHAD07_062 KIT:
o When shutting down a node in a VMScluster, the system that is
being used to perform the shutdown will crash.
o Shadowsets intermittently hang.
o A change has been made in the shadowing code to enhance
performance on systems that make reasonable use of VIOC cache
when a drive is in merge state.
o A new informational message has been added that will result in
a Mount verify message if the IO$_DIAGNOSE function is executed
by the SHDRIVER.
o Additional code changes to improve the error log reporting for
Volume Shadowing.
o The Volume Shadowing code in OpenVMS V7.1 and V6.2, with the
CLUSIO kit installed, included a new algorithm that did not
always guarantee that read requests would be serviced by a
locally connected disk in preference to a disk that was MSCP
served by the host. Prior to V7.1 (and V6.2 with the CLUSIO
kit installed) if there were local and MSCP served disks to
choose from, the request was queued to the local disk unless
the queue depth exceeded twenty.
Some customers who shadowed over FDDI reported that the new
algorithm was not preferable, and therefore requested the
ability to choose the previous behavior.
The ability to prefer that read requests be performed by local
shadow set members, over those served by an OpenVMS system has
been added to this version of the driver. To select that mode
of operation another bit(16) in SHADOW_SYS_DISK has been used.
$ MC SYSGEN
SYSGEN> SHOW SHADOW_SYS_DISK
Parameter Name Current Default Min. Max.
-------------- ------- ------- ------- -------
SHADOW_SYS_DISK 1 0 0 -1
SYSGEN> SET SHADOW_SYS_DISK %X10001
SYSGEN> WRITE CURRENT
SYSGEN> WRITE ACTIVE
SYSGEN> EXIT
PROBLEMS ADDRESSED IN VAXSHAD06_062 KIT:
o A potential system crash with SHADDETINCON bugcheck at
SHDRIVER+12124 during boot from a multi-member shadow set.
This occurs if the booting member is not the first in the
member array, and the other member is not yet visible.
o SHADDETINCON bugchecks occur on multiple nodes in a cluster
during a merge operation.
System crash information
------------------------
Time of system crash: 13-APR-1997 13:21:05.59
Version of system: OpenVMS (TM) VAX Version V6.2
System Version Major ID/Minor ID: 1/0
VAXcluster node: CYV7KE, a VAX 7000-760
Crash CPU ID/Primary CPU ID: 00/00
Bitmask of CPUs active/available: 0000003F/0000003F
CPU 00 reason for Bugcheck: SHADDETINCON, SHADOWING detects
inconsistent state
Process currently executing on this CPU: None
Current IPL: 8 (decimal)
CPU database address: C9212000
MPB address: B29B09C0
CPU 00 Processor stack
General registers:
R0 = 00000000 R1 = B67D258C R2 = B67D2180 R3 = B6544600
R4 = B35992C0 R5 = B624A340 R6 = B65447C8 R7 = 00000000
R8 = B67D2180 R9 = B6544730 R10 = 00000000 R11 = B6544600
AP = B65446B8 FP = 7FE2534C SP = C9213DAC PC = B82E42B3
PSL = 04080000
Processor registers:
P0BR = C9946800 SBR = 1EF80400 ASTLVL = 00000004
P0LR = 0000018B SLR = 003FFF00 SISR = 00000010
P1BR = C9216400 PCBB = 7F7B0020 ICCS = 00000000
P1LR = 001FF116 SCBB = 1EF5F000 SID = 17000201
LDEV = 00018002 LBER = 00000000 LCNR = 00000001
LCON0 = DF0007ED LCON1 = 00000000 TODR = 44D09B64
LBECR0 = 0040003A LBECR1 = 00008060 LMODE = 000332A4
LMERR = 00000000 BIU_STAT = F00E1070 BIU_ADDR = 00000298
MMESTS = 10004005 TBSTS = 800001D0 PCSTS = FFFFF800
ISP = C9213DAC
KSP = 7FFE7800
ESP = 7FFE9800
SSP = 7FFED800
USP = 7FE2534C
o System crashes in SHADDETINCON SYS$SHDRIVER+3D3C0.
Bugcheck Type: SHADDETINCON, SHA RBADC2 (Clustered)
CPU Type: AlphaServer 2100 4/233
VMS Version: V6.2-1H2
Current Process: NULL
Current Image:
Failing PC: FFFFFFFF 8025B3C0
Failing PS: 08000000 00000804
Module: SYS$SHDRIVER
Offset: 0003D3C0
Boot Time: 15-APR-1997 08:39:31.00
System Uptime: 5 22:23
Crash/Primary CPU: 00/00
Saved Processes: 22
Pagesize: 8 KByte (8192 bytes)
Physical Memory: 256 MByte (32768 PFNs)
Dumpfile Pagelets: 184518 blocks
Dump Flags: olddump,writecomp,errlogcomp,dump_style
EXE$GL_FLAGS: poolpging,init,bugdump
Stack Pointers:
KSP = FFFFFFFF 8A731D88 ESP = FFFFFFFF 8A733000 SSP = FFFFFFFF
8A72D000
USP = FFFFFFFF 8A72D000
General Registers:
R0 = 00000000 00000001 R1 = FFFFFFFF 8162F7E0 R2 = FFFFFFFF
8162F7C0
R3 = FFFFFFFF 8186EBC0 R4 = 00000000 00000003 R5 = FFFFFFFF
8162F890
R6 = FFFFFFFF 8186EE80 R7 = 00000000 00000000 R8 = FFFFFFFF
8162F7C0
R9 = FFFFFFFF 8186EDE8 R10 = 00000000 00000000 R11 = FFFFFFFF
8186EBC0
R12 = FFFFFFFF 8186ED38 R13 = FFFFFFFF 8710A270 R14 = FFFFFFFF
87084200
R15 = 00000000 003C60E0 R16 = 00000000 000008B4 R17 = 00000000
00000501
R18 = 00000000 00000000 R19 = FFFFFFFF 87084200 R20 = 00000000
00000000
R21 = FFFFFFFF 8162F808 R22 = FFFFFFFF 8710FB20 R23 = 00000000
00000000
R24 = 00000000 00000001 AI = 00000000 00000001 RA = FFFFFFFF
80288928
PV = FFFFFFFF 8710A698 R28 = 00000000 00000000 FP = FFFFFFFF
8A731DE0
PC = FFFFFFFF 8025B3C4 PS = 08000000 00000804
System Registers:
Page Table Base Register (PTBR) 00000000
00007FF8
Processor Base Register (PRBR) FFFFFFFF
8110A000
Privileged Context Block Base (PCBB) 00000000
0110A080
System Control Block Base (SCBB) 00000000
000001B3
Software Interrupt Summary Register (SISR) 00000000
00000000
Address Space Number (ASN) 00000000
00000000
AST Summary / AST Enable (ASTSR_ASTEN) 00000000
00000000
Floating-Point Enable (FEN) 00000000
00000000
Interrupt Priority Level (IPL) 00000000
00000008
Machine Check Error Summary (MCES) 00000000
00000000
Virtual Page Table Base Register (VPTB) 00000002
00000000
Failing Instruction:
SYS$SHDRIVER_NPRO+393C0: BUGCHK
Instruction Stream (last 20 instructions):
SYS$SHDRIVER_NPRO+39370: RET R31,(R28)
SYS$SHDRIVER_NPRO+39374: LDQ_U R31,(SP)
SYS$SHDRIVER_NPRO+39378: SUBQ SP,#X10,SP
SYS$SHDRIVER_NPRO+3937C: STQ R16,#X0008(SP)
SYS$SHDRIVER_NPRO+39380: STQ R17,(SP)
SYS$SHDRIVER_NPRO+39384: LDQ R17,#XF8E0(R13)
SYS$SHDRIVER_NPRO+39388: BIS R17,#X04,R17
SYS$SHDRIVER_NPRO+3938C: BIS R31,R17,R16
SYS$SHDRIVER_NPRO+39390: LDQ R17,(SP)
SYS$SHDRIVER_NPRO+39394: ADDQ SP,#X08,SP
SYS$SHDRIVER_NPRO+39398: BUGCHK
SYS$SHDRIVER_NPRO+3939C: HALT
SYS$SHDRIVER_NPRO+393A0: SUBQ SP,#X10,SP
SYS$SHDRIVER_NPRO+393A4: STQ R16,#X0008(SP)
SYS$SHDRIVER_NPRO+393A8: STQ R17,(SP)
SYS$SHDRIVER_NPRO+393AC: LDQ R17,#XF8E0(R13)
SYS$SHDRIVER_NPRO+393B0: BIS R17,#X04,R17
SYS$SHDRIVER_NPRO+393B4: BIS R31,R17,R16
SYS$SHDRIVER_NPRO+393B8: LDQ R17,(SP)
SYS$SHDRIVER_NPRO+393BC: ADDQ SP,#X08,SP
SYS$SHDRIVER_NPRO+393C0: BUGCHK
SYS$SHDRIVER_NPRO+393C4: HALT
SYS$SHDRIVER_NPRO+393C8: BIS R31,R31,R31
SYS$SHDRIVER_NPRO+393CC: BIS R31,R31,R31
SYS$SHDRIVER_NPRO+393D0: SUBQ SP,#X50,SP
o The Volume Shadowing software which was shipped in OpenVMS
Alpha and VAX V7.1 and the CLUSIO remedial kits, requires
additional non-paged pool to improve synchronization.
Customers should take this into account when they are tuning
their systems, and be aware that Volume Shadowing is now more
sensitive to resource problems with the possibility that
systems may crash if non-paged pool is exhausted.
Shadowing uses approximately 800 bytes additional non-paged
pool per concurrent IO to the virtual unit. This remedial kit
includes codes which avoids system crashes if a system
exhausts non-paged pool.
Please be aware that there are still cases under which
Non-Paged Pool exhaustion will result in a SHADDETINCON
bugcheck. This modification reduces the probability but
does not completely eliminate them.
o During internal testing, a system crash occurred which
indicated that IOs were left outstanding in DUDRIVER after
a virtual unit had been removed.
o There was a missing index on a check for member valid in the
BBR_READ_RECOVERY routine.
o There was an "infinite" loop condition at SHCP$START_QUED, and
the code has been modified so that the persistent thread will
be "killed" if the VU it has spawned fails.
o This remedial kit includes additional error logging capabilities
to collect additional information when a virtual unit is made
available.
The new LOG_IT macro code has the following input parameters:
o R0 - value of P4
o R1 - value of P5
o R2 - address of LW in SHAD containing P6
o R3 - VU UCB
o R5 - SHAD IRP address with:
- CDRP$L_BCNT = P1
- CDRP$L_MEDIA = P2
- CDRP$L_PID = P3
The implementation makes use of the following cells in the
errorlog record.
o EMB$W_SP_BOFF - set to %xBADE as TAG
o EMB$W_SP_FUNC - reason code
o EMB$L_SP_BCNT - LW for information
o EMB$L_SP_MEDIA - LW for information
o EMB$L_SP_RQPID - LW for information
o EMB$Q_SP_IOSB - 2 LW for information
o EMB$L_SP_CMDREF - LW for Information
o A process may intermittently hang during dismount of a
shadow-set while waiting for completion of the QIOW in
the DO_IO routine.
o KRNLSTAKNV halt during MOUNT/CLUSTER DSAx:
Bugcheck Type: CPUSANITY, CPU sanity timer expired
Node: AI84 (Clustered)
CPU Type: AlphaServer 8400 Model EV56/440
VMS Version: V6.2-1H3
Current Process: PM2SKZ
Current Image: DSA40:[ZENT410.][EXE]BUS.EXE
Failing PC: FFFFFFFF 8001F8D0
Failing PS: 18000000 00001604
Module: SYSTEM_PRIMITIVES_MIN
Offset: 0000B8D0
Boot Time: 26-JUN-1997 08:34:37.00
System Uptime: 1 00:46:34.07
Crash/Primary CPU: 01/00
Saved Processes: 26
Pagesize: 8 KByte (8192 bytes)
Physical Memory: 2048 MByte (262144 PFNs)
Dumpfile Pagelets: 999974 blocks
Dump Flags: writecomp,errlogcomp,dump_style
EXE$GL_FLAGS: poolpging,init,bugdump,pgflfrag
Stack Pointers:
KSP = 00000000 7FF91C98 ESP = 00000000 7FF96000 SSP = 00000000
7FF9C100
USP = 00000000 7EDE4030
General Registers:
R0 = 00000000 00000000 R1 = FFFFFFFF 814EA180 R2 = FFFFFFFF
81410000
R3 = FFFFFFFF 9DE268F8 R4 = 00000000 0000012C R5 = 00000000
7FF91D40
R6 = 00000000 7FF445A0 R7 = 08000000 00000200 R8 = FFFFFFFF
F7710250
R9 = 00000000 00000030 R10 = 00000000 00000031 R11 = 00000000
00000001
R12 = 00000000 00008001 R13 = FFFFFFFF 9DE268F8 R14 = FFFFFFFF
9DE25640
R15 = FFFFFFFF 9DE04200 R16 = 00000000 00000774 R17 = 00000000
7FF91C38
R18 = FFFFFFFF 9DE32CE0 R19 = FFFFFFFF 9DE04200 R20 = 00000000
00000000
R21 = 00000000 272007F0 R22 = FFFFFFFF 9DE04200 R23 = 00000000
00000000
R24 = FFFFFFFF 9DE04AC0 AI = 00000000 00000000 RA = FFFFFFFF
00000000
PV = FFFFFFFF FFFFFFFF R28 = FFFFFFFF 8001F83C FP = 00000000
7FF91E10
PC = FFFFFFFF 8001F8D4 PS = 18000000 00001604
Failing Instruction:
EXE$HWCLKINT_C+00510: BUGCHK
o The system crashes when a second node attempts to boot a system disk
shadow set with two members. The following SHADDETINCON bugcheck at
SHDRIVER+12124 or SYS$SHDRIVER_NPRO+449B4 occurs:
SHADDETINCON, SHADOWING detects inconsistent state
o The mount of a shadow set fails. The failure report says that
the set is already mounted or that there is a duplicate unit
number.
INSTALLATION NOTES:
The images in this kit will not take effect until the system is
rebooted.
If you have other nodes in your VMS cluster, they must also be
rebooted in order to make use of the new images. If it is not
possible or convenient to reboot the entire cluster at this time, a
rolling re-boot may be performed.
This patch can be found at any of these sites:
Colorado Site
Georgia Site
Files on this server are as follows:
vaxshad09_062.README
vaxshad09_062.CHKSUM
vaxshad09_062.CVRLET_TXT
vaxshad09_062.a-dcx_vaxexe
vaxshad09_062.CVRLET_TXT
|
