OpenVMS VAXCLIU03_060 VAX V6.0 SET/SHOW ECO Summary

 
NOTE:  An OpenVMS saveset or PCSI installation file is stored
       on the Internet in a self-expanding compressed file.
       The name of the compressed file will be kit_name-dcx_vaxexe
       for OpenVMS VAX or kit_name-dcx_axpexe for OpenVMS Alpha.
 
       Once the file is copied to your system, it can be expanded
       by typing RUN compressed_file.  The resultant file will
       be the OpenVMS saveset or PCSI installation file which
       can be used to install the ECO.
 

Copyright (c) Digital Equipment Corporation 1994, 1997.  All rights reserved.

PRODUCT:     OpenVMS VAX

COMPONENTS:  CLIUTL - SET.EXE
                      SHOW.EXE 

SOURCE:      Digital Equipment Corporation

ECO INFORMATION:

     ECO Kit Name:  VAXCLIU03_060
     ECO Kits Superseded by This ECO Kit:  VAXCLIU02_070  (V6.0 Only)
                                           VAXCLIU01_062  (V6.0 Only)
                                           VAXCLIU02_060
                                           VAXCLIU01_060 
     ECO Kit Approximate Size:  695 Blocks
     Kit Applies To:  OpenVMS VAX V6.0
     System/Cluster Reboot Necessary:  No

     Installation Rating:  3 - To be installed on all systems running
                               the listed versions of OpenVMS which
                               are experiencing the problems described.

     NOTE:  In order to receive the full fixes listed in this kit,
            the following remedial kits also need to be installed:

                 VAXVERI01_071 for OpenVMS VAX V6.0 only 


ECO KIT SUMMARY:

An ECO kit exists for the DCL commands 'SET' and 'SHOW' on OpenVMS VAX
V6.0.  This kit addresses the following problems: 

Problems Addressed in the VAXCLIU03_060 Kit:

  o  These OpenVMS VAX V6.0 problem corrections were included in the
     multi-version VAXCLIU02_070 remedial kit.  They are now being issued
     as a V6.0 only remedial kit. 

     There are no new problem corrections in this remedial kit.


Problems Addressed in the VAXCLIU01_062 Kit for OpenVMS VAX V6.0:

  o  The index file of a disk can become corrupted.  Closer examination
     of the index file will show that a large number of blocks in the
     index file, at contiguous VBNs from the start of the file, will have
     two words corrupted in the file at offsets 0x3a and 0x1FE.  These
     correspond to the locations of checksum1 and checksum2 in a volume
     home block (homeblock). 

     NOTE:  In order to receive this full fix, the VAXVERI01_071 ECO kit
            must also be installed on your system. 


Problems Addressed in the VAXCLIU02_060 Kit:

  o  If a user with OPER privileges issues either one of the following
     DCL commands, the system will crash with a fatal bugcheck:

          SET TERMINAL/PROTOCOL=NONE RTA0
     or
          SET TERMINAL/PROTOCOL=DDCMP RTA0

     This problem is fixed in OpenVMS VAX V6.1.


Problems Addressed in the VAXCLIU01_060 Kit:

  o  The VT510 terminal is not correctly identified as a member of the
     VT500 series of terminals. 


INSTALLATION NOTES:

The system does not need to be rebooted after this kit is installed.
However, if you have other nodes in your OpenVMS VMScluster, they should
be rebooted or you should install this kit on each system in order to
make use of the new image(s). 

Colorado Site
Georgia Site

vaxcliu03_060.README
vaxcliu03_060.CHKSUM
vaxcliu03_060.CVRLET_TXT
vaxcliu03_060.a-dcx_vaxexe