Title and Copyright Information
 
About This Manual
Audience
Organization
Related Documents
Reader's Comments
Conventions
 
1    Features
1.1    Changes from TruCluster Server Version 5.1
1.1.1    Name of Cluster Interconnect Virtual Device Changed
 
2    Restrictions
2.1    Hardware Restriction
2.1.1    Restrictions on Memory Channel 2 on a GS80, GS160, or GS320 System
2.2    CFS Restrictions
2.3    AdvFS Restriction
2.4    Restrictions on Use of Internet Protocol Version 6 (IPv6)
2.5    Restrictions on Multiple Network Interfaces
 
3    Issues and Known Problems
3.1    Installation
3.1.1    Update to Latest Firmware Before Installing Tru64 UNIX Version 5.1A
3.1.2    Do Not Use the Installation Branch of the Software Option of the SysMan Menu
3.2    Cluster Creation and Member Addition
3.2.1    Conflict in Use of the Default Physical Cluster Interconnect IP Name
3.2.2    Misleading LAN Interconnect Information Provided by clu_create
3.2.3    The clu_create Command Does Not Add the First Member's Fully Qualified Hostname to the /etc/cfgmgr.auth File
3.2.4    Re-adding a Member with clu_add_member -c Does Not Correctly Configure NetRAIN
3.2.5    Run /sbin/kreg After Building Kernel with No Kernel Layered Products
3.3    Booting and Shutdown
3.3.1    Do Not Reboot All Members Simultaneously
3.3.2    AlphaServer GS80/160/320 May Hang on Boot
3.3.3    A Member May Hang on Boot in a Cluster Using a KZPBA-CB SCSI Bus Adapter
3.3.4    Booting Member Hangs While Setting Time and Date with ntpdate
3.3.5    CNX Panic During Boot
3.3.6    Member Hangs During Clusterwide Shutdown
3.3.7    Booting a New Member Without a Cluster License Displays ATTENTION Message
3.3.8    Boot All Cluster Members Before Starting Applications That Use the Memory Channel API Library
3.3.9    "Cannot make specified change" Message During Boot
3.3.10    Booting a Member During Disaster Recovery
3.4    Cluster Configuration
3.4.1    Configurations That Support Ethernet Hubs
3.4.2    Set Ethernet Switch Address Aging to 15 Seconds
3.4.3    On LAN-based Clusters, Add Physical Network Addresses to ifaccess.conf
3.4.4    Whenever Changing Network Interfaces, Update ifaccess.conf
3.4.5    Configuring a Cluster Member as a DHCP Server
3.4.6    After Entering TruCluster Server License Information, Run lmf reset
3.4.7    Deleting a Member with an Inaccessible or Bad Member Boot Disk
3.5    File System
3.5.1    Do Not Create UFS File Systems on a Quorum Disk
3.5.2    CFS Relocation Failures Involving Applications That Wire Memory
3.6    LSM
3.6.1    LSM Commands Fail When Disk Left in Failing State
3.6.2    Problem Encapsulating Swap in Clusters with Long Host Names
3.6.3    Problem Encapsulating Swap When Remote Member Swap Areas Are Already Queued for Encapsulation
3.6.4    The voldisk list Command Does Not Display All Non-LSM Disks in a Cluster
3.7    CAA
3.7.1    Failure Threshold Value Should Not Be Greater Than 10
3.7.2    Problems with caa_relocate When Multiple Interdependent Applications Are Specified
3.7.3    Action Scripts PATH Considerations
3.7.4    The caa_register -u Command Does Not Correctly Update a Nonapplication Resource's State
3.7.5    Changes to HOSTING_MEMBERS List Can Leave Applications Running on Disallowed Members
3.7.6    CAA Events Are Malformed When Viewed from the Event Manager (EVM) Viewer
3.7.7    CAA Lets You Update a Running Application's Required Resources
3.7.8    SysMan Station Shows CAA Application Resources in UNKNOWN State as Having an Error
3.8    Rolling Upgrade
3.8.1    Rolling Upgrade: Do Not Shut Down a Cluster Member To Single-User Mode
3.8.2    Stop prpasswdd Prior to Rolling Upgrade on Clusters Running Enhanced Security Environment
3.8.3    Updating Worldwide Language Support from CD-ROM During a Rolling Upgrade
3.8.4    Run Updates to dop Database Only on Upgraded Members
3.8.5    Recovering from a Failed Install Stage During a Rolling Upgrade from V5.1 to V5.1A
3.9    Miscellaneous Administration
3.9.1    RIS Boot Failures When Cluster is RIS Server
3.9.2    The cfsstat Command Can Return Incorrect Statistics
3.9.3    All Tape Writes at Same Density and Compression
3.9.4    Tape Opens Take Long Time to Fail When No Tape Is Present
3.9.5    Avoid Using Block Sizes Greater Than 512K Bytes for Tape Transfers
3.9.6    Disabling Internet Services on a Per-Member Basis
3.9.7    The hwmgr -show comp Command May Report an Inconsistency Error When Creating a Clusterwide Name for a SCSI Device
3.9.8    The hwmgr -scan scsi Command Does Not Work Clusterwide
3.9.9    Adding a Disk to a Running Cluster
3.9.10    Running Process Accounting on Large Clusters Can Exhaust Member Process Quotas
3.10    SysMan Menu
3.10.1    Nonroot Users with No Home Directory Cannot Run System Management Applications
3.11    SysMan Station
3.11.1    SysMan Station Does Not Display Applications with Long Resource Names
3.11.2    Unable to Expand Host Object in a Cluster
3.11.3    SysMan Station Might Display Cluster Status Incorrectly
3.11.4    SysMan Station Might Display New Hardware Objects Incorrectly
3.11.5    Properties Might Not Be Displayed for Selected Objects
3.11.6    Some SysMan Station Applications Display Wrong Target Member Name
3.12    Documentation
3.12.1    Recovering Cluster Root File System
3.12.2    Correct Size of Member Boot Disk a (Boot) Partition
3.12.3    Error in Example of Hexadecimal Format of IP Address
3.12.4    Media Changer Utility, mcutil, Works on Remote Members
3.12.5    Using LSM to Mirror the Cluster Root File System
3.12.6    Migrating from Automount to AutoFS
3.12.6.1    Migrating Without a Reboot
3.12.6.2    Migrating When Rebooting a Cluster Member
3.12.6.3    Migrating When Rebooting the Cluster
3.12.7    Clusterwide IPC--Supported Mechanisms
3.12.8    Software Product Description (SPD) Replaced by QuickSpec
 
Tables
1-1    TruCluster Server Version 5.1A Features
 
Index