DOCUMENT:Q77624 22-NOV-1999 [msdos] TITLE :MS-DOS Shell Fails to Start PRODUCT :Microsoft Disk Operating System PROD/VER:MS-DOS:5.0 OPER/SYS: KEYWORDS:msdos ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft MS-DOS operating system version 5.0 ------------------------------------------------------------------------------- SYMPTOMS ======== MS-DOS Shell won't start after you type "dosshell" (without the quotation marks) at the MS-DOS command prompt. Or, you cannot switch between another program and MS-DOS Shell. CAUSE ===== This problem can be caused by any of the following: - Incorrect video files for a monochrome monitor - A conflict with memory-resident drivers or programs - Incorrect or corrupted MS-DOS Shell files Read the Workaround section of this article, and try the procedures that apply to your computer. If, after performing these steps, you still have problems with MS-DOS Shell, contact Microsoft Product Support Services. NOTE: If you are a network administrator and you have local computers running MS-DOS Shell files from a network DOS directory, contact Microsoft Product Support Services. WORKAROUND ========== Incorrect Video Files for a Monochrome Monitor ---------------------------------------------- Sometimes Setup improperly identifies monochrome monitors and expands incorrect video files. If your computer has a monochrome monitor and you can't start MS-DOS Shell, expand the correct video files as follows: 1. Delete the DOSSHELL.VID file. For example, if the file is in the DOS subdirectory, type the following at the MS-DOS command prompt: " del c:\dos\dosshell.vid " (without the quotation marks) 2. Preserve the DOSSHELL.INI file by renaming it with a different extension, such as .OLD or .BAK. For example, if this file is located in your DOS subdirectory, type the following command at the MS-DOS command prompt: " ren c:\dos\dosshell.ini c:\dos\dosshell.old " (without the quotation marks) 3. Use the following syntax to expand and copy the new files to your DOS directory: expand [drive1:][path1]mono.in_ [drive2:][path2]dosshell.ini expand [drive1:][path1]mono.gr_ [drive2:][path2]dosshell.grb This syntax renames the files as they are expanded and copied. The [drive1:][path1] parameter specifies the location of the compressed file you want to expand. The [drive2:][path2] parameter specifies the location of the expanded file. The MONO.IN_ and MONO.GR_ files are on Disk 3 (5.25-inch disks) or Disk 2 (3.5-inch disks). For example, if the MONO.IN_ file is on a disk in drive A, and you want to expand the file to the DOS directory on drive C, type the following at the MS-DOS command prompt: " expand a:\mono.in_ c:\dos\dosshell.ini " (without the quotation marks) If DOS Shell works now, you have solved the problem. Removing Memory-Resident Programs and Drivers --------------------------------------------- MS-DOS Shell might not work properly if a memory-resident program or driver is running. If you are having problems with MS-DOS Shell, try starting your computer without running memory-resident programs and drivers. To start your computer without running memory-resident programs or drivers: 1. Create a system disk by inserting a formatted disk into drive A and typing the following: " sys c: a: " (without the quotation marks) 2. Make sure the system disk is in drive A and restart your computer by pressing CTRL+ALT+DEL. 3. To determine whether your CONFIG.SYS and AUTOEXEC.BAT files are causing problems, type the following at the MS-DOS command prompt: " c:\dos\dosshell " (without the quotation marks) If MS-DOS Shell starts, one or both of these files are probably causing problems. If MS-DOS Shell doesn't start, these files might not be causing problems, in which case you should skip to the next procedure, "Incorrect or Corrupt MS-DOS Shell Files." 4. Remove the system disk from drive A and restart your computer by pressing CTRL+ALT+DEL. 5. To determine whether your AUTOEXEC.BAT file is causing problems, rename your CONFIG.SYS file by typing the following at the MS-DOS command prompt: " ren config.sys config.bac " (without the quotation marks) 6. Restart your computer by pressing CTRL+ALT+DEL and type the following at the MS-DOS command prompt: " dosshell " (without the quotation marks) If MS-DOS Shell doesn't start, your AUTOEXEC.BAT file is causing problems; proceed to step 7. If MS-DOS Shell starts, the problem is probably with your CONFIG.SYS file, not your AUTOEXEC.BAT file; skip to step 11. 7. Use a text editor, such as MS-DOS Editor, to open the AUTOEXEC.BAT file. If you want to use MS-DOS Editor, type the following command: " edit autoexec.bat " (without the quotation marks) 8. Insert the REM command in front of every command in your AUTOEXEC.BAT file except the @ECHO OFF, PROMPT, and PATH commands. For example, your AUTOEXEC.BAT might look like the following: rem dos\share @echo off prompt $p$g path c:\dos rem temp=c:\temp rem tmp=c:\temp rem init=c:\init rem start workstation rem logon joeblow rem netime time rem net use l: \\john\doe rem net use lpt1: \\john\doe rem mode spe=high rem cd \qs rem quickshr - - - y \qs rem cd \ 9. Save your AUTOEXEC.BAT file. If you're using MS-DOS Editor, choose Save from the File menu. 10. To determine which command is causing a problem, remove the first REM command from the first command line. Save your AUTOEXEC.BAT file, restart your computer by pressing CTRL+ALT+DEL, and try to start MS-DOS Shell by typing "dosshell" (without the quotation marks) at the MS-DOS command prompt. Repeat these steps until MS-DOS Shell does not start. When it doesn't start, you have identified a command that conflicts with MS-DOS Shell. 11. Restart your computer by typing CTRL+ALT+DEL. Then rename your CONFIG.SYS file by typing the following at the MS-DOS command prompt: " ren config.bac config.sys " (without the quotation marks) 12. To determine whether your CONFIG.SYS file is causing problems, rename your AUTOEXEC.BAT file by typing the following at the MS-DOS command prompt: " ren autoexec.bat autoexec.bac " (without the quotation marks) 13. Restart your computer by pressing CTRL+ALT+DEL and type the following at the MS-DOS command prompt: " c:\dos\dosshell " (without the quotation marks) If MS-DOS Shell doesn't start, your CONFIG.SYS file is causing problems; proceed to step 14. If MS-DOS Shell starts, there is probably no problem with your CONFIG.SYS file; skip to step 20. 14. Use a text editor, such as MS-DOS Editor, to open your CONFIG.SYS file. If you are using MS-DOS Editor, type the following at the MS-DOS command prompt: " c:\dos\edit c:\config.sys " (without the quotation marks) 15. Insert the REM command in front of every command in your CONFIG.SYS file except lines with device drivers that are needed to run computer hardware, such as a disk drive, monitor, or keyboard, and lines with FILES and BUFFERS commands. Make sure to type the REM command in front of the mouse driver command, if any. 16. Change the FILES and BUFFERS commands to the following: FILES="30" (without the quotation marks) BUFFERS="30" (without the quotation marks) If your CONFIG.SYS file does not have these commands, add them. 17. Save your CONFIG.SYS file. If you're using MS-DOS Editor, choose Save from the File menu. 18. To determine which driver is causing a problem, remove the first occurrence of the REM command from a command line. Save your CONFIG.SYS file, restart your computer by pressing CTRL+ALT+DEL, and try starting MS-DOS Shell by typing "c:\dos\dosshell" (without the quotation marks) at the MS-DOS command prompt. Repeat these steps until MS-DOS Shell does not start. When it doesn't start, you have identified a command that conflicts with MS-DOS Shell. 19. Rename your AUTOEXEC.BAT file by typing the following at the MS-DOS command prompt: " ren c:\autoexec.bac c:\autoexec.bat " (without the quotation marks) 20. When you have identified the commands that are causing problems, insert the REM command in front of the same commands in the AUTOEXEC.BAT and/or CONFIG.SYS files on drive C. Then restart your computer and try using MS-DOS Shell. If the MS-DOS Shell still doesn't start, you might have more than one command in one or both files that are causing problems. In this case, repeat steps 5 through 19 as applicable. When you have identified the drivers and/or programs that are causing problems, you have two options: - If the drivers and/or programs are not essential, you can disable them with the REM command, as described earlier in this procedure. - You can contact the manufacturers of the drivers and/or programs for further assistance. Incorrect or Corrupt MS-DOS Shell Files --------------------------------------- Sometimes Setup identifies your monitor incorrectly and copies the wrong video files to your system. Also, sometimes video or MS-DOS Shell files become corrupted during or after setup. MS-DOS Shell won't work properly if the following files are incorrect or corrupted: DOSSHELL.EXE DOSSHELL.GRB DOSSHELL.INI DOSSWAP.EXE DOSSHELL.COM DOSSHELL.VID If you are having problems with MS-DOS Shell, try manually expanding these files from your Setup disks, as follows: 1. Preserve DOSSHELL.INI by backing it up with the COPY command. For example, if this file is in the DOS directory, change to the DOS directory by typing "cd \dos" (without the quotation marks) at the MS-DOS command prompt. Then type the following command: " copy dosshell.ini dosshell.old " (without the quotation marks) 2. Use the following syntax to expand and copy the following files to your DOS directory: expand [drive1:][path1]dosshell.ex_ [drive2:][path2]dosshell.exe expand [drive1:][path1]dosshell.co_ [drive2:][path2]dosshell.com expand [drive1:][path1]dosswap.ex_ [drive2:][path2]dosswap.exe The [drive1:][path1] parameter specifies the location of the compressed file you want to expand. The [drive2:][path2] parameter specifies the location of the expanded file. These files are on Disk 3 (5.25-inch disks) or Disk 2 (3.5-inch disks). For example, if the DOSSHELL.EX_ file is on a disk in drive A, and you want to expand the file to the \DOS directory on drive C, type the following at the MS-DOS command prompt: " expand a:\dosshell.ex_ c:\dos\dosshell.exe " (without the quotation marks) 3. Find your monitor type below, and expand and rename the files by typing the specified commands. The files are on Disk 3 (5.25-inch disks) or Disk 2 (3.5-inch disks). Monochrome ---------- expand a:\mono.gr_ c:\dos\dosshell.grb expand a:\mono.in_ c:\dos\dosshell.ini Note that a monochrome monitor does not require a .VID file. CGA --- expand a:\cga.gr_ c:\dos\dosshell.grb expand a:\cga.in_ c:\dos\dosshell.ini expand a:\cga.vi_ c:\dos\dosshell.vid EGA --- expand a:\ega.gr_ c:\dos\dosshell.grb expand a:\ega.in_ c:\dos\dosshell.ini expand a:\ega.vi_ c:\dos\dosshell.vid EGA Monochrome -------------- expand a:\egamono.gr_ c:\dos\dosshell.grb expand a:\mono.in_ c:\dos\dosshell.ini expand a:\ega.vi_ c:\dos\dosshell.vid VGA (Super VGA, XGA, and other high-resolution monitors) -------------------------------------------------------- expand a:\vga.gr_ c:\dos\dosshell.grb expand a:\ega.in_ c:\dos\dosshell.ini expand a:\vga.vi_ c:\dos\dosshell.vid 8514 Color ---------- expand a:\vga.gr_ c:\dos\dosshell.grb expand a:\ega.in_ c:\dos\dosshell.ini expand a:\ega.vi_ c:\dos\dosshell.vid VGA Monochrome (VGA, Super VGA, XGA, and other high-resolution monitors) ---------------------------------------- expand a:\vgamono.gr_ c:\dos\dosshell.grb expand a:\mono.in_ c:\dos\dosshell.ini expand a:\vga.vi_ c:\dos\dosshell.vid 8514 Monochrome --------------- expand a:\vgamono.gr_ c:\dos\dosshell.grb expand a:\mono.in_ c:\dos\dosshell.ini expand a:\cga.vi_ c:\dos\dosshell.vid Hercules -------- expand a:\herc.gr_ c:\dos\dosshell.grb expand a:\mono.in_ c:\dos\dosshell.ini expand a:\herc.vi_ c:\dos\dosshell.vid Additional query words: appnote 5.00 ====================================================================== Keywords : msdos Technology : kbMSDOSSearch kbMSDOS500 Version : MS-DOS:5.0 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.