DOCUMENT:Q73672 21-NOV-1999 [msdos] TITLE :Upgrading to MS-DOS 5.0 over Stacker PRODUCT :Microsoft Disk Operating System PROD/VER:MS-DOS:5.0 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft MS-DOS operating system version 5.0 ------------------------------------------------------------------------------- SUMMARY ======= If you have STAC Electronics Stacker 1.0 installed on your machine and you want to upgrade to MS-DOS version 5.0, follow the procedure below. If any of these steps fail, please contact STAC Electronics technical support by calling (619) 431-6712 or faxing (619) 431-1073. If you Stacker version 2.0 or later, follow the instructions in your Stacker manual to update to MS-DOS 5.0. If you have Stacker version 1.1 or earlier, obtain an automatic update utility from Stac Electronics. MORE INFORMATION ================ To upgrade your machine to MS-DOS 5.0, do the following: 1. IMPORTANT: Back up your hard drive. This is for your benefit. 2. Install MS-DOS 5.0 to floppy disks with the SETUP /F command. 3. Determine which drive is your boot drive using the following procedure: a. Remove any disk from drive A and reboot the machine. b. Insert the Stacker disk in drive A. c. Type "A:\SWAPMAP" (without the quotation marks). d. Record the drive letter that "was drive C: at boot time." For example, in the following sample display of SWAPMAP, drive D is the one you are looking for: Drive A: was drive A: at boot time Drive B: was drive B: at boot time Drive C: was drive D: at boot time [D:\STACVOL.000 = 16.0MB] Drive D: was drive C: at boot time 4. Transfer the system files to the hard drive. Insert the MS-DOS 5.0 Support disk (5.25-inch) or Startup/Support disk (3.5-inch) in the floppy drive. Type "SYS x:" (without the quotation marks), where x is the drive that is swapping with drive C. In the above example, this is drive D. If you are not swapping drives, type "C:" (without the quotation marks). If you are requested to "Insert the system disk in drive A:", insert the Startup disk. If SWAPMAP gives the output "Drive C: was Drive C: at boot time," go to step 6. 5. Note: The MS-DOS SYS command will NOT work on Stacker volumes. This step accomplishes the same thing as the SYS command. a. Remove the MS-DOS 5.0 Startup or Startup/Support disk and insert the Stacker disk. b. In the following commands, x represents the drive that is swapped with drive C. If you are using an IBM version of DOS, the system files are named IBMBIO.COM, and IBMDOS.COM. Use these in place of IO.SYS and MSDOS.SYS. Type the following commands: " sattrib -r -s -h c:\io.sys sattrib -r -s -h c:\msdos.sys sattrib -r -s -h x:\io.sys sattrib -r -s -h x:\msdos.sys copy x:\io.sys c:\ copy x:\msdos.sys c:\ copy x:\command.com c:\ sattrib +r +s +h c:\io.sys sattrib +r +s +h c:\msdos.sys sattrib +r +s +h x:\io.sys sattrib +r +s +h x:\msdos.sys" (without the quotation marks) 6. Copy MS-DOS files as needed. a. Remove the Stacker disk and insert the Startup or Startup/Support disk. b. Use the COPY command to copy some or all of the files to your hard disk. It is a good idea to put the MS-DOS version 5.0 files in the same directory in which you stored your previous MS-DOS files. If you copy the MS-DOS 5.0 files to a different directory, the paths in the CONFIG.SYS and AUTOEXEC.BAT files will be incorrect. c. Insert each of the remaining working disks in the disk drive and copy the files you want. Remember, there will be a DOS directory on the Stacker volume as well as on the uncompressed drive. Make sure you include a copy of COMMAND.COM in your DOS subdirectories. The product included here, Stacker, is manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding this product's performance or reliability. Reference(s): STAC Electronics technical support: Phone (619) 431-6712 Fax (619) 431-1073 Additional query words: 5.00 ====================================================================== Keywords : Technology : kbMSDOSSearch kbMSDOS500 Version : MS-DOS:5.0 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.