"STOP 0xD1" Error Message After You Apply Windows 2000 Service Pack 3 (327083)



The information in this article applies to:

  • Microsoft Windows 2000

This article was previously published under Q327083

SYMPTOMS

After you apply the Windows 2000 Service Pack 3 (SP3) and restart your computer, you may receive the following error message on a blue screen:
STOP 0x000000D1 (0x00000114, 0x00000010, 0x00000000, 0xBFF754CC)
DRIVER_IRQL_NOT_LESS_OR_EQUAL
In this error message, the memory that is referenced is 0x00000114. The IRQL is 0x10 (IRQL 16). Value 0 is a read operation; 1 is a write operation. The address that referenced memory is 0xBFF754CC.

CAUSE

This issue can occur if your computer is using a Promise Ultra100 PCI Controller Card that is using a device driver version (Ultra.sys) earlier than 2.00.0.29.

For additional information about the Promise Ultra100 PCI Controller Card and the device driver packages for the card, visit the Promise Web site:

RESOLUTION

To prevent this issue from occurring, install the updated Ultra.sys driver before you install SP3.

To resolve this issue if you have already applied SP3, follow these steps:
  1. Obtain the updated version of the device driver (Ultra.sys). To do this, visit the following Promise Web site:
  2. Do one of the following:
    • If the partition uses the NTFS file system, use your Windows 2000 CD to start at the recovery console.

      -or-
    • If the partition uses the FAT file system, start the computer by using an MS-DOS boot disk.
    For additional information about how to use your Windows 2000 CD to start at the recovery console, click the article number below to view the article in the Microsoft Knowledge Base:

    301645 HOW TO: Use Recovery Console on a Computer That Does Not Start

  3. Copy the Ultra.sys file (from the Promise Web site) to the Windows 2000 Drivers folder (%Systemroot%\System32\Drivers), overwriting the existing version.
  4. Restart the computer.

WORKAROUND

To work around this issue, if you cannot obtain the updated Ultra.sys driver that is described earlier in this article, you can replace the existing Scsiport.sys file with the version from Microsoft Windows 2000 Service Pack 2 (SP2). To do this, follow these steps.

NOTE: If you use this workaround, several fixes that are included with Windows 2000 SP3 are disabled. Use this method only as a temporary workaround, and then permanently resolve this issue by installing the updated version of the device driver (Ultra.sys) from the Promise Web site.

  1. Do one of the following:
    • If the partition uses the NTFS file system, use your Windows 2000 CD to start at the recovery console.

      -or-
    • If the partition uses the FAT file system, start the computer by using an MS-DOS boot disk.
    For additional information about how to use your Windows 2000 CD to start at the recovery console, click the article number below to view the article in the Microsoft Knowledge Base:

    301645 HOW TO: Use Recovery Console on a Computer That Does Not Start

  2. Copy the Scsiport.sys file (from the Windows CD) to the Windows 2000 Drivers folder (%Systemroot%\System32\Drivers), overwriting the existing version.
  3. Restart the computer.

STATUS

Microsoft has confirmed that this is a problem in the Microsoft products that are listed at the beginning of this article.

MORE INFORMATION

For additional information about Windows 2000 Service Pack 3, click the article number below to view the article in the Microsoft Knowledge Base:

260910 How to Obtain the Latest Windows 2000 Service Pack

Q260910
Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.

The third-party products that are discussed in this article are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, regarding the performance or reliability of these products.

Modification Type:MajorLast Reviewed:10/17/2006
Keywords:kbfix kbprb KB327083