Conformance to ADO 2.0 and OLE DB 2.0 (183558)
The information in this article applies to:
- Microsoft OLE DB Provider for AS/400 and VSAM 1.0, when used with:
This article was previously published under Q183558 SYMPTOMS
This is a list of nonconformance problems that may occur:
IDBProperties->GetPropertyInfo is not level 0 compliant for certain
properties.
IOpenRowset::OpenRowset gives incorrect results when rgPropertySets = NULL
and cPropertySets <> 0.
IOpenRowset::OpenRowset fails when rgProperties is NULL and cPropertySets
<> 0.
IOpenRowset::OpenRowset returns incorrect error when TableID is NULL.
Opening rowset produces incorrect error when a SETIFCHEAP property set is
not set.
IOpenRowset::OpenRowset fails to return an error when properties are set
incorrectly.
IOpenRowset::OpenRowset does not give correct errors when table ID = NULL.
IDBProperties::GetPropertyInfo causes an exception.
When IDBProperties::GetProperties fails, *prgPropertySets should be NULL
but is not.
IDBProperties tests cause an assertion failure.
QueryInterface for IID_IConnectionPointContainer gives E_NOINTERFACE.
CODBProperty::Save makes unsmurfy call to VariantChangeType--this breaks
IPersistFile::Save.
Attempting to set data to the bookmark column does not result in correct
status value IRowsetNewRow::BMK_key_curs_immed v1.
IRowsetupdate::Insertrow should return DB_E_BADACCESSORHANDLE when accessor
= 0 iRowsetNewRow::bound_key_immed v1.
ISessionProperties::GetProperties needs to return null prgPropertySets when
error occurs.
An exception is caused in CODBPropertyManager::GetProperties when it gets
invalid arguments.
Assertion fails in CODBPropertyManager::GetAllProperties -- ulcount = 0.
Another assertion failure--in CODBPropertyManager::GetProperties
rgPropertyIDSets[i].cPropertyIDs = 0.
An exception is caused in CODBPropertyManager::SetProperties when it gets
invalid arguments.
CreateAccessor does not detect binding err conditions well and if it did
detect an error condition, it would not return an error code
IAccessor::TCCreateValidRowAccessors v12.
IConvertType::CanConvert has no validity checking (or use of)
dwConvertFlags icnvttyp::TCcanconvert v5.
Getting DBSCHEMA_INDEXES causes an exception.
GetPropertyInfo does not return correct output values when E_INVALIDARG
occurs.
IRowset->TCIRowset_RetrieveData variation 5 causes an exception in
IdataConvert.
CODBIRowsetLocate::GetNextRows does not return correct values when given
invalid arguments IRowset::TCIRowset_Boundary::V7.
CODBIRowsetUpdate::SetData needs to validate arguments before returning
with no error.
When IOpenRowset::OpenRowset fails, ppRowset should be null.
IOpenRowset::OpenRowset returns incorrect error when TableID's pwszName is
bad IOpenrowset::Openrowset v68,69,72, 73.
Opening rowset produces incorrect error when a SETIFCHEAP property is not
succesfully set.
CODBPropertyManager::SetProperties never notices if dwOptions specifies a
bad option.
IOpenRowset::OpenRowset deliberately sets properties even though they are
read-only.
An invalid colid (in the DBPROP structure) is ignored by
CODBPropertyManager::SetProperties.
IOpenRowset::OpenRowset does not check that the interface in riid is
supported when pprowset = NULL.
IOpenrowset::Openrowset v46 fails because we return an invalid hr.
STATUS
Microsoft has confirmed this to be a problem in SNA Server 4.0's OLE DB
Provider for AS/400 and VSAM version 1.0.
A supported fix is now available, but has not been fully regression
tested and should be applied only to systems experiencing this specific
problem. Unless you are severely impacted by this specific problem,
Microsoft recommends that you wait for the next service pack that contains
this fix. Contact Microsoft Technical Support for more information.
| Modification Type: | Minor | Last Reviewed: | 3/18/2004 |
|---|
| Keywords: | kbbug kbfix KB183558 |
|---|
|