Removing Non-DOS Partitions with Debug (106419)

SUMMARY

Introduction

There are currently several different versions of MS-DOS in the personal-computer environment, both in the OEM-licensed versions and in the Microsoft packaged-product versions. The hard-disk-management capabilities of MS-DOS vary from one version to another. For example, MS-DOS versions 3.2 and 3.21 can address a single hard-disk partition of up to 32 megabytes (MB); MS-DOS version 3.3 can address multiple hard-disk partitions, with a primary DOS partition of up to 32 MB and an extended DOS partition containing logical drives of up to 32 MB each; and MS-DOS versions 4.0, 4.01, 5.0, 6.0, and 6.2 can address multiple hard-disk partitions with sizes up to 2 gigabytes (GB).

For those using versions of MS-DOS that have lesser levels of hard- disk support, such as MS-DOS versions 3.2 and 3.21, there are a number of third-party hard-disk-management software packages that allow MS- DOS to access multiple partitions and/or partitions in excess of 32 MB. However, these third-party packages may use non-DOS constructs to assist in managing the hard disk, possibly including non-DOS partitions. These non-DOS constructs can cause problems when you upgrade to later versions of MS-DOS because versions of MS-DOS earlier than 5.0 assume that non-DOS constructs are owned by another operating system and, therefore, do not use, delete, or change non-DOS partitions or other non-DOS constructs in any way. To detect if your system makes use of Drive Overlay software, see the following article:

Using Debug to Remove a Non-DOS Partition

The Debug script on the following page, used with the MS-DOS Debug program, deletes non-DOS partitions when you upgrade to a new version of MS-DOS, enabling the entire hard disk to be used by MS-DOS. It does so, however, by clearing out the entire partition table on the hard disk, which results in the deletion of ALL partitions on the hard disk. You need to use this method if your current version of MS-DOS cannot delete non-DOS partitions. There are two ways to use the following Debug script:

• Run Debug and type the Debug commands from the center column of Table 1 at the corresponding Debug prompt. (The left column of the table shows the prompts that are displayed by Debug. You do not need to type the comments in the right column.)

  -or-

• Type the command in the center column of Table 1 into a file using a text editor such as MS-DOS Editor and then use input redirection to feed the resulting file into Debug. For example, if you typed the commands into a file called HDPART.SCR, you would clear your partition table by typing the following at the MS-DOS command prompt and then pressing ENTER:

  debug < hdpart.scr

        Table 1:  Debug Script to Erase Hard-Disk Partition Table
     ----------------------------------------------------------------
        Debug        Enter Debug       Comments
        Prompts      Commands
     ----------------------------------------------------------------
        -            A 100             Assemble from CS:0100.
  
        nnnn:0100    INT 13            Call interrupt 13.
  
        nnnn:0102    press the         (nnnn in the segment address).
                     ENTER key
  
        -            RAX               Replace AX register.
  
        AX 0000
  
        :            0301              Write on sector.
  
        -            RBX               Replace BX register.
  
        BX 0000
  
        :            0200              Start from ES:200.
  
        -            F 200 L 200 0     We want to write zeros.
  
        -            RCX               Replace CX register.
  
        CX 0000
  
        :            0001              Cylinder, 0, sector 1.
  
        -            RDX               Replace DX register.
  
        DX 0000
  
        :            0080              First physical hard disk, head
                                       0. (Substitute 0081 for this
                                       entry if you are clearing the
                                       table on the second physical
                                       hard disk, 0082 if you are
                                       clearing the third physical
                                       hard disk, and so forth).
  
        -            P                 Proceed (Debug will display
                                       several lines of information).
  
        -            Q                 Quit Debug.
     ----------------------------------------------------------------
  						

This script completely clears the partition table on your hard disk, preparing the hard disk for repartitioning using the MS-DOS Fdisk program. (When you run Fdisk for the first time after using this procedure and before reinstalling MS-DOS, the message "No partitions defined" should be displayed if the partition deletion procedure was successful.) For more information about using Fdisk, see the Microsoft MS-DOS" User's Guide and Reference" for version 3.2, 3.21, 3.3, 4.0, 4.01, or 5.0, or the Microsoft MS-DOS" User's Guide" for version 6.0 or 6.2.

For additional information on how to recreate a partition using the Fdisk utility, click the article number below to view the article in the Microsoft Knowledge Base: Non-DOS partitions on your hard disk are also erased if you perform a low-level format. Consult your hardware manufacturer for specific instructions on performing a low-level format on your hard disk.