How to Display Network Registry Parameters (102469)



The information in this article applies to:

  • Microsoft Windows NT Server 3.1
  • Microsoft Windows NT Workstation 3.1
  • Microsoft Windows NT Advanced Server 3.1
  • Microsoft Windows NT Server 3.51
  • Microsoft Windows NT Server 4.0
  • Microsoft Windows NT Workstation 3.51
  • Microsoft Windows NT Workstation 4.0

This article was previously published under Q102469

SUMMARY

You can get most of the Lan Manager Server and Workstation parameters to appear in the registry automatically by using the NET CONFIG command.

WARNING: When you run NET CONFIG SERVER (or NET CONFIG SRV), server related parameters that are normally autoconfigured each time you boot (for example, maxworkitems)are permanently set in the registry to whatever values Windows NT is currently using. These parameters will continue to override the defaults until you change them in the registry. You cannot change the values by running Control Panel, choosing Server, and then choosing Configure. Consequently, if you add or remove memory, or change the server size setting (minimize/balance/maximize), you will not get the benefit of server autoconfiguration.

MORE INFORMATION

By default, the only parameters in the

HKEY_LOCAL_MACHINE

\SYSTEM\CurrentControlSet\Services\LanmanServer\Parameters



section of the registry are the following:

                         Size  3
                   Lmannounce  0
				


Windows NT 3.51 and 4.0 have the following additional entries:
                                 ==========
				


                          NullSessionPipes
                         NullSessionShares
				


However, if you type the following at the command line

C:\>net config server /HIDDEN:NO
The command completed successfully.



you will see the following appear in the registry:

HKEY_LOCAL_MACHINE\SYSTEM

\CurrentControlSet\Services\LanmanServer\parameters



                         Size  3
                   Lmannounce  0
                      comment  ""
                   srvcomment  ""
                        users  -1
                         disc  15
               autodisconnect  15
                       hidden  1
                     announce  720
                     anndelta  3000
                     userpath  "c:\"
                    sessopens  2048
                      sessvcs  1
                   opensearch  2048
                 maxworkitems  128
                 maxrawbuflen  65535
                    sessusers  2048
                    sessconns  2048
          maxpagedmemoryusage  -1
       maxnonpagedmemoryusage  -1
             enablesoftcompat  1
           enableforcedlogoff  1
                   timesource  0
				


Windows NT 3.51 and 4.0 have the same above entries EXCEPT the "disc" and the "comment" are eliminated.

                      comment
                         disc
				


This situation also applies to the Lan Manager Workstation section of the registry. By default the

HKEY_LOCAL_MACHINE

\SYSTEM\CurrentControlSet\Services\Lanmanworkstation\parameters



section of the registry is empty. However, if you type

net config work /CHARTIME:250



the following appears:

HKEY_LOCAL_MACHINE

\SYSTEM\CurrentControlSet\Services\Lanmanworkstation\parameters



                     CharWait  3600
           MaxCollectionCount  16
               CollectionTime  250
                     KeepConn  600
                      MaxCmds  50
                  SessTimeout  45
                   SizCharBuf  512
                   MaxThreads  17
                    LockQuota  6144
                LockIncrement  10
                  LockMaximum  500
                PipeIncrement  10
                  PipeMaximum  500
             CacheFileTimeout  10
             DormantFileLimit  45
          ReadAheadThroughput  -1
              MailslotBuffers  8
        ServerAnnounceBuffers  20
     NumIllegalDatagramEvents  5
     IllegalDatagramResetTime  60
           LogElectionPackets  0
      UseOpportunisticLocking  1
              UseUnlockBehind  1
               UseCloseBehind  1
                BufNamedPipes  1
            UseLockReadUnlock  1
             UtilizeNtCaching  1
                   UseRawRead  1
                  UseRawWrite  1
              UseWriteRawData  1
                UseEncryption  1
            BufFilesDenyWrite  1
             BufReadOnlyFiles  1
          ForceCoreCreateMode  1
        Use512ByteMaxTransfer  0
				


Windows NT 3.51 and 4.0 have the same above entries.

Modification Type:MajorLast Reviewed:8/8/2001
Keywords:kbenv KB102469