Storage Automated Diagnostic Environment
Patch 114591-22 Release Notes

Part Number:  817-0192-10
Mar/20/06
=========================

READ BEFORE USING THIS REVISION

The Release Notes contain information specific to this
revision. This information is not elsewhere in the
product documentation set.

The Release Notes for this product are on the product media.
You can print them as you would any other ASCII file.


Copyright 2003 Sun Microsystems, Inc., 901 San Antonio Road,
Palo Alto, CA 94303 USA. All rights reserved.

This product or document is protected by copyright and distributed
under licenses restricting its use, copying, distribution, and
decompilation. No part of this product or document may be reproduced
in any form by any means without prior written authorization of Sun
and its licensors, if any. Third-party software, including font
technology, is copyrighted and licensed from Sun suppliers.

Parts of the product may be derived from Berkeley BSD systems, licensed
from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open
Company, Ltd.

Sun, Sun Microsystems, the Sun logo, AnswerBook, Sun StorEdge, Sun
StorTools, Sun StorEdge T3, and Solaris  are trademarks, registered
trademarks, or service marks of Sun Microsystems, Inc. in the U.S.
and other countries. All SPARC trademarks are used under license
and are trademarks or registered trademarks of SPARC International,
Inc. in the U.S. and  other countries. Products bearing SPARC
trademarks are based upon an architecture developed by Sun
Microsystems, Inc.


The OPEN LOOK and Sun(TM) Graphical User Interface was developed by
Sun Microsystems, Inc. for its users and licensees. Sun acknowledges the
pioneering efforts of Xerox in researching and developing the concept of
visual or graphical user interfaces for the computer industry. Sun holds
a non-exclusive license from Xerox to the Xerox Graphical User Interface,
which license also covers Sun's licensees who implement OPEN LOOK
GUIs and otherwise comply with Sun's written license agreements.

RESTRICTED RIGHTS: Use, duplication, or disclosure by the U.S. Government
is subject to restrictions of FAR 52.227-14(g)(2)(6/87) and FAR
52.227-19(6/87), or DFAR 252.227-7015(b)(6/95) and DFAR 227.7202-3(a).

DOCUMENTATION  IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS,
REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO
BE LEGALLY INVALID.

Copyright 2003 Sun Microsystems, Inc., 901 San Antonio Road,
Palo Alto, CA 94303 Etats-Unis. Tous droits reserves.

Ce produit ou document est protege par un  copyright et distribue avec des
licences qui en restreignent l'utilisation, la copie, la distribution,
et la decompilation. Aucune partie de ce produit ou document ne peut etre
reproduite sous aucune forme, par quelque moyen que ce soit, sans
l'autorisation prealable et ecrite de Sun et de ses bailleurs de licence,
s'il y en a. Le logiciel detenu par des tiers, et qui comprend la
technologie relative aux polices de caracteres, est protege par un
copyright et licencie par des fournisseurs de Sun.

Des parties de ce produit pourront etre derivees des systemes
Berkeley BSD licencies par l'Universite de Californie. UNIX est une
marque deposee  aux Etats-Unis et dans d'autres pays et licenciee
exclusivement par X/Open Company, Ltd.

Sun, Sun Microsystems, le logo Sun, AnswerBook, Sun StorEdge, Sun
StorTools, Sun StorEdge T3, et Solaris  sont des marques de fabrique
ou des marques deposees, ou marques de service, de Sun Microsystems, Inc.
aux Etats-Unis et dans d'autres pays. Toutes les marques SPARC sont
utilisees sous licence et sont des marques de fabrique ou des marques
deposees de SPARC International, Inc. aux Etats-Unis et dans d'autres
pays.  Les produits portant les marques SPARC sont bases sur une
architecture developpee par Sun Microsystems, Inc.

L'interface d'utilisation graphique OPEN LOOK et Sun(TM) a ete
developpee par Sun Microsystems, Inc. pour ses utilisateurs et licencies.
Sun reconnait les efforts de pionniers de Xerox pour la recherche et le
developpement du concept des interfaces d'utilisation visuelle ou
graphique pour l'industrie de l'informatique. Sun detient une licence
non exclusive de Xerox sur l'interface d'utilisation graphique Xerox,
cette licence couvrant egalement  les licencies de Sun qui mettent en
place l'interface d'utilisation graphique OPEN LOOK et qui en outre se
conforment aux licences ecrites de Sun.

CETTE PUBLICATION EST FOURNIE "EN L'ETAT" ET AUCUNE GARANTIE,
EXPRESSE OU IMPLICITE, N'EST ACCORDEE, Y COMPRIS DES GARANTIES
CONCERNANT LA VALEUR MARCHANDE, L'APTITUDE DE LA PUBLICATION
A REPONDRE A UNE UTILISATION PARTICULIERE, OU LE FAIT
QU'ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS.
CE DENI DE GARANTIE NE S'APPLIQUERAIT PAS, DANS LA MESURE
OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU.


DOCUMENT STRUCTURE
==================
These Release Notes contain the following sections:

o Introduction
o Audience
o Deliverables
o Related Documentation
o Qualified Platforms
o New Features
o Installation Instructions
o Product Hints
o Known Problems
o Resolved Problems
o Media Contents


INTRODUCTION
============
The Storage Automated Diagnostic Environment 2.2 package
provides a graphical user interface, enabling the user to remotely
monitor and diagnose Sun storage devices.  The Agent can be used
to collect data and analyze the condition of Sun StorEdge devices.
The Diagnostics can be used to verify the condition
of a system, identify failing FRUs and verify FRU replacement.


AUDIENCE
========
The Storage Automated Diagnostic Environment is for use by
system administrators and support personnel
who are familiar with Sun's disk array and SAN products.


DELIVERABLES
============
Documentation Delivered With This Product
-----------------------------------------
The following documentation is delivered with this product:

Application     Title
-----------     -----

Man Pages
 		6120ofdg.1m
                6120ondg.1m
		6120volverify.1m
                brocadetest.1m
                checkcron.1m
                clearcache.1m
                config_solution.1m
                discman.1m
                disk_inquiry.1m
                ifptest.1m
                lbf.1m
                linktest.1m
                qlctest.1m
                ras_admin.1m
                ras_fccheck.1m
                ras_install.1m
                ras_revcheck.1m
                rasagent.1m
                sanbox.1m
                save_password.1m
                snapshot.1m
                stresstest.1m
                switchtest.1m
                switch2test.1m
                t3ofdg.1m
                t3volverify.1m
                testt3.1m
                vediag.1m
                veluntest.1m


User/Admin      Storage Automated Diagnostic Environment
                2.2 User's Guide (817-0192-10)




PRODUCT PACKAGING
=================
The Storage Automated Diagnostic Environment 2.2 software is
distributed as an unbundled product in the pkgadd format as SUNWstads.


RELATED DOCUMENTATION
=====================
Sun StorEdge T3 and T3+ Array documentation:
    Sun StorEdge T3 and T3+ Array Start Here (816-0772-10)
    Sun StorEdge T3 and T3+ Array Installation, Operations and
                            Service Manual (816-0773-10)
    Sun StorEdge T3 and T3+ Array Administrator's Guide (816-0776-10)
    Sun StorEdge T3 and T3+ Array Configuration Guide (816-0777-10)
    Sun StorEdge T3 and T3+ Array Site Preperation Guide (816-0778-10)
    Sun StorEdge T3 and T3+ Field Service Manual (816-0779-10)
    Sun StorEdge T3 and T3+ Array Release Notes (816-0781-12)

Sun StorEdge Network FC Switch-8 and Switch-16 documentation:
    Sun StorEdge Network FC Switch-8 and Switch-16 Installation and Config
                                                   Guide (806-6922-10)
    Sun StorEdge Network FC Switch-8 and Switch-16 Field Troubleshooting
                                                   Guide (816-0252-10)
    Sun StorEdge Network FC Switch-8 and Switch-16 Release Notes (816-0842-15)

Sun StorEdge Network 2 Gb FC Switch-8, Switch-16, and Switch-64 documentation:
    Sun StorEdge SAN 4.0 Release Guide to Documentation (816-4470-10)
    Sun StorEdge SAN 4.0 Release Installation Guide (816-4469-10)
    Sun StorEdge SAN 4.0 Release Configuration Guide (806-5513-10)
    Sun StorEdge SAN 4.0 Release Notes (816-4472-10)


McData ED6064 and ES3232 FC switches:
    The following documents may be found on the McData Website,
       http://www.mcdata.com:
     Intrepid TM 6064 Director Planning Manual
     Intrepid TM 6064 Director Manager User Manual
     SAN Plannning Guide
     Manager Software User Manual
     Command Line Interface User Manual

     This information can be found under:
       Knowledge Center Link -> Technical Documents

     Additional publications are available by means of McData's secure web
     site. Please contact webmaster@mcdata.com for access.



Sun StorEdge 3900 and 6900 Series documentation:
    Sun StorEdge 3900 and 6900 Series Reference and Service Guide (816-5253-10)
    Sun StorEdge 3900 and 6900 Series Site Perperation Guide (816-5256-10)
    Sun StorEdge 3900 and 6900 Series Regulatory and Safety Compliance
                                      Manual ( 816-5257-10)
    Sun StorEdge 3900 and 6900 Series Installation Guide (816-5252-10)
    Sun StorEdge 3900 and 6900 Series Troubleshooting Guide (816-5255-10)


Solaris:
    Solaris Handbook for Sun Perihperals (806-2210-10)


QUALIFIED PLATFORMS
===================
You can use the SUNWstads package on the following platforms and
operating systems:


Sun Platforms        : Sun StorEdge Service Processor

Sun StorEdge         : Sun StorEdge 3900 series
                       Sun StorEdge 6900 series
		       Sun StorEdge 6320 series
                       Sun StorEdge T3 array (F/W 1.17 or greater)
                       Sun StorEdge T3+ array (F/W 2.0 or greater)
                       Sun StorEdge 6120 array
		       Sun StorEdge 3510 FC Array


SAN                  : Sun StorEdge Network FC Switch-8 and Switch-16.
                       Sun StorEdge Network 2 Gb FC Switch-8, Switch-16
                       and Switch-64.
                       Brocade Silkworm 2400/2800 FC Switch
                       Brocade Silkworm 3200/3800/12000 FC Switch
		       McData ED6064 FC Switch
		       McData ES3232 FC Switch

Operating Systems    : Solaris 9
                       Solaris 8 4/01 or greater.

Browsers:            : Netscape 4.76, 6.x, 7.x, IE 5.x, 6.x

Perl                 : 5.005 or better is mandatory.  Use the following URL
                       to acquire the proper version if necessary.
                       http://www.perl.com/pub/language/info/software.html

                       If the proper version does in fact already exist,
                       create a symbolic link of the executable to
                       /usr/bin/perl.


FEATURES
========
o Collects and reports information about Sun StorEdge Solutions. Types of
  information includes device configuration, device statistics, device
  state and availability, device message-log information, and
  system configuration.

o Incorporates a graphical user view of FC StorEdge devices and the
  intercoonects.

o Contains an event grid that provides recommended service actions for
  each event.

o Creates a model of the device and its components, storing state
  information about that device and saving log information.

o Contains revision checking functionality of Fiber Channel devices.


INSTALLATION INSTRUCTIONS
=========================
o Review the User's Guide which applies to your locale

o Following the ras_install procedure, connect to the
  system using a supported browser using port 7654.
  (ie. http://{hostname}:7654)

o Default login as user "ras" with the password "agent". THe default
  ras password can be changed under Admin->System Utilities->Root
  Password.  Additional user's can also be added under Admin->System
  Utilities->Login/Roles.

o Follow the "Basic Installation Steps" or Select "Basic Steps in Popup"
  from the Master's Home Page. Complete all required steps.

o Revision Checking should be run before creating a topology.
  Updating all firmware and software components to the current revisions,
  ensures that the devices have the capabilities required to be
  discovered, monitored and diagnosed properly.



PRODUCT HINTS
=============
o StorADE is a device monitoring tool that probes devices on the ethernet
  and for direct attached storage devices, accesses the device on the
  datapath (Fibre Channel).
  ***************************************************************************
  ***************************************************************************
  For most storage arrays, it is important to queiesce any and all monitoring
  during upgrade operations.
  ***************************************************************************
  ***************************************************************************

  Use the following information that best suits
  this site for stopping StorADE from monitoring:

  Stopping StorADE
  ----------------
  There are several ways to accomplish the task of stopping the StorADE
  monitoring agents from probing a storage array during an upgrade.

  One way would be to disable the specific agent from executing.  This would
  allow for the continuing of the monitoring of other types of devices.

    Disabling the Agent
    -------------------
      GUI
      ---
        Select General Maintenance -> Maintain Hosts -> host_name
        Deselect the Device as a Category to monitor -> Submit

      CLI
      ---
        There is no cli command in 2.0 to directly affect individual
        categories to monitor.

  The most efficient way to stop StorADE from monitoring entirely would
  be to set the stop bit or stop the cron from executing.

    Disabling StorADE
    -----------------
      GUI
      ---
        Select General Maintenance -> Stop Agents -> Stop -> Submit

      CLI
      ---
        Execute ras_install and select "P" to postpone the execution of
        rasagent from cron.  This will remove the cron entry that starts
        the agent every 5 minutes.

        NOTE: This will not immediately stop any existing execution of
        the StorADE agent.  Use the 'ps` command to ensure all storade
        activity has ended.

                 `ps -ef | grep ras'

o If a Sun StorEdge 3510 FC array was already discovered before applying this
  patch, the user will need to delete this device, rediscover the device and
  create a new topology snapshot after applying this patch.

o You should be familiar with UNIX commands and Sun's disk array
  products before attempting to use this product.

o System administrators should know about security risks associated with
  installing a web server. Take the appropriate action to protect access
  to the SUNWstade port 7654.

o In order to launch the Configuration Service browser, you must install the
  packages with the same security options which is normally security turned
  on.

o Must use "/opt/SUNWstade" as the package base directory.

o When installing a new patch to SUNWstade:
  stop the agents before installing the update
  and execute the /opt/SUNWstade/bin/ras_install program
  after installing the update

o If there are existing problems with a storage device when the package
  is installed, these problems may not be detected or reported.
  They will, however, generate an event (type of event is based on the
  type of failure) when the error condition is corrected.

o Brocade FC Switch configurations using segmented loop
  (SL) zones can be monitored and diagnosed but the topology
  views will not show connections between devices.

o switchtest and linktest may not provide diagnostics for
  fibre channel links between downrev'd HBAs and/or downrev'd switches
  as well as fibre channel links between switches and virtualization
  engines (VE). This is a result of the current lack of support for the
  fabric ECHO test command in these products.

o SE 3600/6900 series solutions must have the file
  /var/opt/SUNWstade/DATA/Inventory.golden
  created on the Service Processor before bringing up the GUI.
  This is performed at the factory. However, if an upgrade is performed
  execute /opt/SUNWstade/sysbin/config_solution on
  the Service Processor to update the file.

  This enables proper discovery of the Sun StorEdge 3600/6900 Series.

o Some browsers such as Netscape 7 will prompt for a username/password
  when applets are loaded.  Enter the same username/password which was
  used to initially log in.

o When using Netscape 6.2.1 with SSL enabled the user MUST point
  the browser to https://hostname w/o the port #.

o When using Netscape 4.79 the following error may occur if
  seperate browser sessions are initiated from the command line.

  #error The certificate issuer for this server is not recongized by Netscape.
  The security certificate may or may not valid.
  Netscape refuses to connect to this server (-8179) java40.tar/ifc11.jar
  java.lang.SecurityExcpetion: system classes not signed

  exit Netscape (close all windows)

  Solaris:
  cd .netscape
  mv key3.db key3.bad
  mv cert7.db cert7.bad
  restart Netscape

  Windows:
  C:/Program Files/Netscape/Users/username/
  rename key3.db key3.bad
  rename cert7.db cert7.bad


2.2 CHANGES AND ENHANCEMENTS
============================
o  Added monitoring support for McData ED6064 and ES3232 FC switches
o  Support 3900SL/6900SL
o  Support StorEdge 6120
o  Support StorEdge 6320
o  Support StorEdge 3510

RESOLVED PROBLEMS with patch 114591-22
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
5013520 Power Sequencer state toggles 'ON'  'ERR' no activities performed
5030987 2.2 3910/6910 Config diagnostic test gets Execution error from Client/Diag.pm sc
6278533 sa2.2: se_extract is not creating a valid tar image
6295809 SE6320: Storade device summary doesn't display all the slices when there is a gap within the LUN
6357172 Update SA 2.2 revision matrix to support new Array FW 3.2.3  and 3.2.4

RESOLVED PROBLEMS with patch 114591-21
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4987866 Notices thru SNMP Trap Provider
5015938 Missing new battery status for 3.1.x or better fmwr
5019795 "Disabled" string a reg expression in policy file
5019079 ISP2300[2] OFFLINE is probably host reboot event
5042198 Patch Report Status is always in "Running" state w/N4.79
5083496 Aggregate messages to SSRR
6183219 Unable to generate Patch and Package information
6179240 SSRR Heartbeat frequency is too fast
6191019 Backup Events occur every day.
6191017 Sync Audit events for 2.2 and 2.4
6190986 Add BEFIT syslog message enhancements to StorADE 2.2
6191015 Enhancements to the instructions for online disk firmware upgrades.
6191014 Enhancements to the message log scrubbing for array firmware 3.2.
6179410 6120s in 6320 show up as seperate devices.
5106496 NSCC: For 6020/6120 NWS_Battery & CIM_PhysicalPackage Name needs to be unique
6193584 NRI: BETA: disk verify log events should not generate Storade events
6182541 an alarm is being generated for CacheMirror/Mode disabled on DELETED volumes
5106332 6320: array controller firmware revision not reported
5031601 need to sync se_extract with 2.4 version
6183369  2.2: volCacheMode/Mirror is not correct severity at start
6191015 SA2.2: Enhancements to the instructions for online disk firmware upgrades.
6207893 Allow ability to put severity=X in array_policies file
6240564 sa2.2: telnet activity from a script causes an alarm to be downgraded to non-Actionable
6252275 Revision check fails with latest SA 2.2 patch on a 39xx/6910/6960 products

RESOLVED PROBLEMS with patch 114591-20
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4988579 SA2.2:Sense key events in the log are generating 2 separate events
4977589 NSCC: 6020 firmware versions are not part of telemetry
4986165 disk error messages in the log should be reclassified as a notice
4899903 change Sense Key 0x3 0x11 and 0x1 0x18 errors to notice
4976847 Recovered disksense event 38.20.100 severity to high
4983823 se_extract should be included in -20 patch to support 3.x array fmwr
4992191 advisor actions for ALL sense key events say to replace disk

RESOLVED PROBLEMS with patch 114591-19
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4966573 config_solution new array gateway/hostname not set
4930391 read the SSRR rss_params file for site information fields cust and site, etc.
4948022 Configure a 6120 to be a 6020 in a 6320 system environment

RESOLVED PROBLEMS with patch 114591-18
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4914276 fru key for a t3 controller is wwn where all other frus are serial number
4938476 Discrepancy in supported OS version for patch 11459x_17
4909107 storade keeps new_sp name after maserati has been through setup
4943498 Can't change patch source from CD since it corrupts patchpro.conf
4928657 volSafety token not working

RESOLVED PROBLEMS with patch 114591-17
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4892162 se_extract command needs to be in ras_remote.list
4909107 storade keeps new_sp name after maserati has been through setup

RESOLVED PROBLEMS with patch 114591-16
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4903568 M32: StorAde should not call patchpro several times during patch installation


RESOLVED PROBLEMS with patch 114591-15
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------

RESOLVED PROBLEMS with patch 114591-14
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4901254 se_extract does not capture t3/6020 messages file
4901258 se_extract only captures the DATA dir as a symbolic link

RESOLVED PROBLEMS with patch 114591-13
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4839017 Revision Checking displays ERR for Fujitsu drive.
4853385 url does not give usefull information
4868384 6120-loop diag failure doesn't provide and recommended actions
4868564 volume verification status under device summary does not have a completed status
4868569 there is no error indication from a failure with emailing using the SMTP library
4868937 Path to Email Program field in Config Option has no functional value if entered
4868941 the selection for activating vol verify is not very clear
4869099 patch matrix has downrev patchid for 113722 (current = -02)
4869180 the home page of the GUI indicates VolVerify:ON even though no DAY/TIME selected
4844855 Update recommended actions for switch2 event 12.5.7
4868945 add some verbage to the volverify window to slect a day and time is required
4869792 Matrix config-matrix_3.15.001 doesn't list latest available on 2 patches

4816026 Manage > Service  > Configure Devices does not appear to work
4860116 Array passwords should be encrypted but are shown on Manage-->Array Password
4822097 Incorrectly reporting "Number of LUN(s) changed from 16 to 0".
4827582 Loop card box in topology is not red, health shows alert 21.20.91 indicating bad
4840826 Cannot see or edit script info in e-mail notification after initial setup
4853518 Admin Login/Roles incomplete information
4863175 Can't locate object method "encrypt_email" via package "Email"
4864266 M32:Changing array passwd thru StorADE doesn't register the passwd with mgmnt sw
4866003 Volslice size diff between 6320 and whats displayed when monitored as a device

4823224 Storade needs consistency in capacity reporting
4853063 (maserati) Monitor Device Page has an empty right-hand side
4855064 event advisor window shows critical messages with error indicator not do
4856412 Pulled d2 disk causes actionable alert 6.26.18 which isn't in Service Ad
4856994 an array_warning log event was emailed with an event code showing ERR.20
4858335 D2 event 6.26.18 when a disk is pulled isn't listed in the Service Advis
4859184 Actionable VE event 16.12.31 not listed in Service Advisor
4860762 there is no description for volverify pull-down in maintain devices -> d
4718451 Agent reports: ERR  CIM_ER Key field must have value!::
4739330 Re-discover button not used consistantly
4750800 Admin > General > Config Options > Production site? is unclear, not docu
4785073 Need recommended action/cause for EventType: TopologyEvent.remove.disk_f
4787060 Cannot view man pages for t3ofdg in gui
4792771 QuiesceEndEvent and QuiesceEndStart event need clarification in text
4795561 Agent run with SUNWstads package shows "skipping 3310"
4797802 Cannot view the 6120 diagnostic man pages from the gui
4801608 T4:Monitor Devices > Device Report does not have links for loop, fc_stat
4801783 Help for Device Report Screen
4806946 config_solution had timout/killing proc error during execution
4814139 Need to document and add an event for host being monitored by DE1.2
4814199 Event 18.20.90 doesn't have any probable causes or recommended actions
4818406 Cannot log out of StorADE GUI
4823915 Description field contains unreferenced numbers in SUNWstads email notif
4824885 No event generated when array is unconfigured in Manage > Service > Conf
4825502 se2 events 20.37.84 and 20.37.35 for 6320 not listed in service advisor
4826229 No description available in Service Advisor for 6120 event 21.3.115
4826235 6120 cache event 21.3.86 not listed in Service Advisor
4826338 No e-mail sent after PatchPro uprades an SP
4827556 Received event 4.3.99 referring to t3, device is actually a 6120
4828567 Help Search functionality deficient
4830013 Clear Event Maximums does not work if agent is running.
4834067 Configuration Summary does not detect Notif. Providers
4836950 fru stat shows no temp on drives and storade says temp is over 68
4837229 Patch Report Status does not automatically refresh
4837948 ras_patchlist does not show any output
4838139 Text formatting not user freindly in Manage > Service > Revision Mainten
4839103 Help Diagnose>Diagnostic Tests has a misleading label.
4840014 Admin > General > Add E-mail notification > Admin Group needs to be docu
4841739 Reminder e-mails should be sent when agent stops monitoring for disk dow
4849326 E-mailed event doesn't indicate which slave was added to the master host
4850162 Welcome screen on SUNWstads page indicates 1 6320 and 1 6120 in solution
4850165 Welcome screen on SUNWstads indicates 3900/6900: 1 6320 in configuration
4852572 6120 21.3.56 and t3 event 13.3.56 event/severity should match (time diff
4853487 Skipping message - have exceeded threshold/time count on rule3 on agent
4854834 Radio buttons within the GUI guide in help are selectable
4856576 message that alerts will be cleared is displayed after rasagent -d2 comp
4858655 6320 Rev. Main.:User should not be allowed to select device if there is
4862332 GUI Guide content for General Reports > Temperature Reports & Temp Summa
4862346  Local Notification (Email/Scripts) > Turn Off Event Advisor
4863072 Clicking on Fru Summary in General > Fru Reports shows info from Detaile
4864714 M32:System edition of StorADE on the SP has references to 'T3's.
4865342 linktest available from monitor topology
4865423 When trying to launch the UI on Indy w/2.1 from 2.2 it fails.
4727128 Topology layout "Default" should be the default

4859305 Execution error: Undefined subroutine &GUI::FruReport::frus0&health=1

4842285 Switchtest2 fails with loopback connector on 64 port Qlogic switch
4800915 After saving layout on topology if I do a new snapshot I lose my saved l
4824219 Storade should have a button to click to see patchpro install report
4833576 Create aggregrated event for disconnected loop interconnect cable.
4833943 Topology does not show any status change after a "partial shutdown" of r
4837148 Warning message needs to be updated in Manage > Service > Revision Maint
4840308 No visual indication in Summary report for disconnected Loop Cable.
4840352 Storade version 2.2.00.03 reports incorrect number of volumes on T3's.
4844920 se_extract should capture SP image info.
4846721 Summary report for host is reporting LUN as T4 lun instead of 6320 lun
4847625 stop updating Vol_Verify Process-Kill Log window once the kills are comp
4847650 "Refreshing Battery" Notice msg in T3logfile is emailed as a Warning n/a
4847651 volume.u2vol1.volOper=verifying should not be a warning
4848075 storade captures controller reset messages returned by logger command
4848615 No entry in service advisor for se event 20.20.308.
4848772 Topology does not show FC errors on links between host and 6320.
4849250 Event 4.3.99 needs to have "check array password" in recommended actions
4851382 Clearing events while ras is running causes events during that run to be
4852602 installing the 114590-11c patch resets my t3 passwords for vol verify
4852718 (maserati) Reports on device health format broken and inconsistent with
4853046 Cannot logout from stroade2
4853526 same test option names exist in Set Defaults menu for different tests
4854954 Reports -> Fru Reports -> Fru Summary (Health Concerns) fails to email r
4857089 Reports > General > Array performance does not work in SUNWstads package
4859028 add an option to send nscc_email provider with encryption on
4859030 create a new exception report that is customizable by the client
4784978 Storade event not showing up on SUNWmc console
4837369 Running ras_patchlist doesn't show the user any information
4840191 Administration(GUI):System partially shutdown-invalid Overall Health sta
4840698 Title bar only shows Root user by Storade level, doesn't show others
4858405 Default diagnostic Email setting lost
4719849 Usage for ras_discover shows -? for help, comes back with no match
4644252 add the ras_install script to be executed during package/patch postinsta
4818112 summary report on frus should include output, battery, temp, fans
4849553 increase frequency setting beyond 2 hour limit
4817763 add ability to customize severity for site based alerts
4850166 add the ability to disable the Event Advisor information from local emai
4851196 Add a report that would indicate a range of temps of all FRU's in a sing

RESOLVED PROBLEMS with patch 114591-11
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4851314 Cannot add 6910 with SP version 2.3.1 as a monitored device
4838032 Start Devices should be renamed to let users know they can also Stop Dev
4840297 Event Code 21.5.25 icon does not match between heath and Service Advisor
4803871 EventCode for T4 Lun failover is 7.4.ERR.
4828963 Launch 6320 from Monitor > Devices > SE2 tries to call the same SP via t
4840153 Ran agent and saw the following error: FCRule8: cannot find : in TO
4850708 Change "monitored hosts" to "monitoring hosts"
4815522 allow to monitor t3 in parallel to improve frequency
4621527 srs provider is able to be updated with an invalid or empty IP Address f

RESOLVED PROBLEMS with patch 114591-10
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4841721 On 6960 - config GUI add component to VE zone sometimes fails
4841891 getting an error on my indy running SE.pm
4841467 Run continuous vol verify shows "Default" instead of actual setting
4840035 Release Notes for patches 114591-10a and 114590-10a repeat themselves
4840741 Change t3 passwords missing from Admin > Utilities > Scripts in SUNWstads
4840009 Problems installing patch 114591-10a, indicates return code 127
4714183 Request for CLI command to generate a textual representation of SAN toplogy
4712966 T3 disk port bypass status is displayed as both critical (red) and alert (yellow
4723680 Event grid has no entry for the category of San, LinkEvent.SIG.ve|switch
4768831 Update aggregated message when a single t3 brick is discovered
4771139 Man page for config_solution in SUNWstads pkg needs to updated with 6320 info
4761515 References to non relevant device/host names in event grid
4788597 T3 "Key" Field needs explanation under maintain devices.
4800898 Remove the "Filter" box in the SUNWstads topology windows
4801872 Help for Display History Screen
4802350 Basic Installation popup is not sized correctly
4796462 Topology displayed when first entering diags from topo is not the saved one's
4803834 Help for Discovery Screen
4806379 Monitor > Monitor Log > Agent Errors does not show correct info
4806386 Monitor > Devices > Graph doesn't match what is in documentation
4809344 Loop cable being disconnected should be an actionable event (21.5.25)
4816735 Add 6120 to Admin > Sys Utilities > Run Scripts
4817772 local notify function requires valid email when scripting
4817769 add missing fields to script options in local notification
4818106 code 13.5.37 for t3 batstate does not exist where a code of 13.5.38 does
4818120 event reports with an empty email address still says "Email Sent!" w/no error
4818158 email config function does not include the devices
4818963 Inventory.golden identifies PSX-1000 as VICOM, has wrong WWN and serial number
4819036 StorADE advisor did not report error as actionable nor did it advise.
4816982 Monitor Topology incorrectly shows CacheMode as writeThrough on 6120.
4819090 no longer generate actionable event on sense key 0x1 unless asc=0x5d
4818046 debug/http code showing up in 2.2.00.03 on 1st page of config 3900/6900
4819823 On 6120, actionable event 21.5.38, fruPowerBatState is [Undefined]
4818067 email notification shows a 91:Actionable in the viewing page if sev selected
4812692 add logic to recognize the Notice message about a disk download command in log
4820483 disk states from fault-disabled to fault-substituted are not actionable
4821241 Launching 6320 from Monitor Devices brings up a blank browser window
4821452 M25: Discovery of T3/T3B does not work - results in No response from host
4821422 M25: Sun 2G 8-port switch listed as type Switch1
4822004 Info for initial aggregated event stuck to the last event
4821291 6120 event 21.5.38 should include "check airflow" in recommended actions
4818129 the note about no verification during clear cache should be bright red
4822186 Remove "Update All Hosts" from Maintain Hosts in SUNWstads
4822086 Health view shows red alert but service advisor shows yellow for same fault.
4822286 Storade 2.2 - Monitoring State off is not reflected in Maintain Device
4822264 StorADE Monitor Topology inccorrectly reports u1 as red
4822871 SUNWstads, Manage > Revision Setup > Copy CD, incorrectly indicates "Copying"
4823084 Need ability to clear alerts via CLI
4824232 Manage > Revision Maintenance, window does not automatically refresh
4824530 Monitor severity is not consistent.
4825083 Inadequate ether message.
4824281 6120: Email event is indicating wrong controller of T4.
4825614 StorAde is not sending topology to the nscc
4826318 StorADE is indicating changing from WriteThrough to WriteBehind as an Error
4827359 Link Errors do not have Event Codes.
4828252 StorAde Web front end does not work through web proxies
4833374 Revisions of 6120 fw expected in 114285-03 are displayed as uprev

RESOLVED PROBLEMS with patch 114591-04
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4831910 6120-loop test on SP shows Multiple hosts to run from
4825107 M26: StorADE loop test fails from SP
4831483 Agent crashes due to missing loopinf.htm file on T3's
4825068 6120:Loopback test does not work with loopback connector installed.
4812891 T4 linktest calls out T3B in interactive text message.
4822908 6120:When linktest isolates to 6120; SA should take extra step to replace SFP

RESOLVED PROBLEMS with patch 114591-03
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4825440 StorADE not properly setting PatchPRO proxy host

RESOLVED PROBLEMS with patch 114591-02
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4821351 Monitor Devices doesn't list Indy devices even after running the config_solution
4820926 M25: Monitor Devices does not list the 6120 array
4820886 M25: Maintain Devices and Start Devices lists the wrong SP hostname
4822878 Manage > Revision Setup > Update options, incorrectly indicates "updated"
4824414 User Roles are added if incorrect user/pwd combination used to try to login
4824398 Test in Manage > Utilities > Array Passwords is confusing
4824234 Need help info and text in window in Manage > Revision Setup

RESOLVED PROBLEMS with patch 114591-01
======================================
Bug Id  Synopsis
------- ------------------------------------------------------------------
4812861 Monitoring software does not indicate which path saw loop statistics increments
4811489 Remove references to T3 that are viewable to customer
4815915 M25: Maintain Hosts should not list Sun T3 under Update Hosts for SUWNstads pkg
4815009 event grid code 21.5.37 does not exist in 6120.grid
4818780 should use script for health monitoring of SE6320 USB relay device


KNOWN, UNRESOLVED PROBLEMS
==========================
o 4812682 add logic to recognize an upgrade process and consequently block
          access
  Be sure to disable StorADE from monitoring while upgrading T3 disk firmware.

o 4825088 6120:Loopback test does not work with loopback connector installed
  Until this bug is fixed by the array firmware, StorADE will indicate
  that the array is bad, even though it may be okay.


2.2 PATCH MEDIA CONTENTS
========================
See README
