HP Services Software Patches - vaxmscp03_062

 
NOTE:  An OpenVMS saveset or PCSI installation file is stored
       on the Internet in a self-expanding compressed file.
       The name of the compressed file will be kit_name-dcx_vaxexe
       for OpenVMS VAX or kit_name-dcx_axpexe for OpenVMS Alpha.
 
       Once the file is copied to your system, it can be expanded
       by typing RUN compressed_file.  The resultant file will
       be the OpenVMS saveset or PCSI installation file which
       can be used to install the ECO.
 
Copyright (c) Digital Equipment Corporation 1997, 1998.  All rights reserved.

OP/SYS:     DIGITAL OpenVMS VAX

COMPONENT:  TMSCP.EXE
            MSCP.EXE

SOURCE:     Digital Equipment Corporation

ECO INFORMATION:

     ECO Kit Name:  VAXMSCP03_062
     ECO Kits Superseded by This ECO Kit:  VAXMSCP02_062
                                           VAXMSCP01_062
                                           VAXMSCP01_070
     ECO Kit Approximate Size:  144 Blocks
     Kit Applies To:  OpenVMS VAX V6.2 
     System/Cluster Reboot Necessary:  Yes

     Installation Rating:  2 - To be installed on all systems running
                               the listed version(s) of OpenVMS and
                               using the following feature(s):
                                
                               Systems that MSCP serve tapes and disks

     NOTE:  The following remedial kit(s) must be installed BEFORE
            installation of this kit:

                 VAXCLUSIO01_062


ECO KIT SUMMARY:

An ECO kit exists for TMSCP and MSCP on OpenVMS VAX V6.2.  This kit 
addresses the following problems: 

Problems addressed in VAXMSCP03_062

  o  The VAXMSCP02_062 remedial kit required that the VAXCLUSIO01_062 
     kit be installed.  If the user tried to install the VAXMSCP02_062 
     kit on a system that had both the VAXCLUSIO01_062 and OpenVMS 
     VAX Y2K remedial kits installed, the VAXMSCP02_062 kit did not 
     recognize that the VAXCLUSIO01_062 kit had been installed.  This 
     caused the VAXMSCP02_062 installation to fail.

     There are no new ECO problem corrections in this kit.  If you
     have installed the VAXMSCP02_062 remedial kit, you do not need
     to install the VAXMSCP03_062 remedial kit.


Problems addressed in VAXMSCP02_062

  o  If a customer upgraded their system to V6.2 from V6.1, the
     KITINSTAL.COM procedure, in kits that require the VAXCLUSIO01
     remedial kit to be installed first, did not properly verify
     that the VAXCLUSIO01_062 remedial kit had been installed.


Problems addressed in VAXMSCP01_062

  o  TMSCP does not restore R2 properly before using the register
     as an MSCP message.  This misuse manifests either in a
     corrupted TMSCP$ERR_TBL which causes devices to be inaccessible, 
     or the system will crash.  The outcome depends on the value in
     R2.

     This misuse is manifested as either a corrupted TMSCP$ERR_TBL,
     which is the cause of the devices not being accessible, or as a
     system crash, depending on the value in R2.

  o  The client process hangs when it attempts to mount a tape device
     that is online to another host.  Mount issues a packack for the 
     device.  The client then issues an ONLINE command.  During 
     TMSCP/ONLINE processing, if the server finds an HQB address in 
     the UQB$L_ONLINE_HQB field, it returns SUCCESS status with an 
     ALONL subcode even though the HQB is not for the requesting host.

     When the client processes the successful ONLINE end message, it
     issues a GUS.  The server returns a unit-available for this
     command which causes the client TUDRIVER to reissue an ONLINE
     which starts the process all over again.  It stays in this
     loop forever.

  o  An INVEXCEPTN system crash may occur when TMSCP does not get a  
     message buffer during configuration when a connection to 
     MSCP$TAPE is broken.

  o  An inconsistent transfer count occurs when a forced error on a
     drive is encountered.  A drive directly attached (or HSx
     served) reports a different transfer count than the same drive
     served via the MSCP server.

     Code that attempts to determine the LBN of a forced error
     block by looking at the byte count in the IOST/IOSB will
     arrive at different values on the same drive when directly
     accessed or MSCP served.


Problems addressed in VAXMSCP01_070 for V6.2

  o  The problem occurs when ERASE commands with history logging are
     issued  on  MSCP  clients  for  large numbers of blocks to MSCP
     devices served by an OpenVMS MSCP server.  On an Alpha  server,
     an  "Illegal  Command" entry will be posted in the system error
     log and  the  command  will  be  aborted.   Typically,  if  the
     affected  device  is  part  of a shadow set, the set will enter
     mount verification and the I/O  request  will  eventually  fail
     with a "Fatal Controller Error".  On a VAX server, no immediate
     problem is noticed but the possibility of corrupting  a  shadow
     set  exists  should  there be a failure during the execution of
     the ERASE command and a mini-merge is performed  when  the  set
     becomes available.

  o  A satellite node will not  boot  after  a  preferpath/forcepath
     command is issued on the server.

  o  Word instructions are used to reference a byte field.


INSTALLATION NOTES:

The images in this kit will not take effect until the system is
rebooted.

If you have other nodes in your VMS cluster, they must also be
rebooted in order to make use of the new image(s).  If it is not
possible or convenient to reboot the entire cluster at this time,




Files on this server are as follows:

Files on this server are as follows:

»vaxmscp03_062.README
»vaxmscp03_062.CHKSUM
»vaxmscp03_062.CVRLET_TXT
»vaxmscp03_062.a-dcx_vaxexe