DOCUMENT:Q172122 10-AUG-2001 [winnt] TITLE :Toshiba I586 Pro 230 MHz System and the National 307 Chip PRODUCT :Microsoft Windows NT PROD/VER:WinNT:4.0 OPER/SYS: KEYWORDS:kbhw kbWinNT400sp4fix kbHardware ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation version 4.0 - Microsoft Windows NT Server version 4.0 - Microsoft Windows NT Server version 4.0, Terminal Server Edition ------------------------------------------------------------------------------- SYMPTOMS ======== Windows NT may not recognize the COM2 port on a Toshiba computer. CAUSE ===== Some Intel motherboards included in Toshiba computers support COM2 as an infrared (IR) device. If the COM2 port is set in the BIOS to Infrared Data Access Mode, Windows NT does not recognize it. If COM2 is set as a serial port, Windows NT recognizes it and makes it available automatically. Windows NT fails to recognize the National 307 chip on the Intel motherboard included in some Toshiba computers. During Detection, Windows NT runs the DoesPortExist() function that reads the serial port's line control register. The COM2 port test usually returns 0x00; however, the infrared port returns 0x5C. The COM2 port is not available because Windows NT writes this returned value to the wrong registers in the device. RESOLUTION ========== Perform one of the following to resolve this problem: - Manually install the COM2 port. Please refer to the manufacturer's instructions for making changes to your CMOS settings. 1. Before Windows NT is installed, start the CMOS setup routine on the Toshiba PC. From the CMOS settings, change the infrared (IR) port to COM:2. When you install Windows NT, it will properly install the COM:2 port. 2. If Windows NT is already installed, ensure the CMOS is set to COM2: (see step 1), then perform the following steps: a. Click the Start button, point to Settings, and then click Control Panel. b. Double-click the Ports icon, select COM2:, and then click Settings. Click Advanced, and then from the Settings for COM2 Port dialog box, select 03f8 for the Base I/O Port Address and 4 for the Interrupt Request Line. Click OK. - To resolve this problem, obtain the latest service pack for Windows NT 4.0 or Windows NT Server 4.0, Terminal Server Edition. For additional information, please see the following article in the Microsoft Knowledge Base: Q152734 How to Obtain the Latest Windows NT 4.0 Service Pack STATUS ====== Microsoft has confirmed this to be a problem in Windows NT 4.0 and Windows NT Server 4.0, Terminal Server Edition. This problem was first corrected in Windows NT 4.0 Service Pack 4.0 and Windows NT Server 4.0, Terminal Server Edition Service Pack 4. ====================================================================== Keywords : kbhw kbWinNT400sp4fix kbHardware Technology : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT400search kbWinNTSsearch kbWinNTS400search kbWinNTS400 kbNTTermServ400 kbNTTermServSearch Version : WinNT:4.0 Issue type : kbbug Solution Type : kbfix ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.