DOCUMENT:Q166828  25-FEB-2002  [winnt]
TITLE   :Upgrade Installation of Windows NT 4.0 Results In STOP Errors
PRODUCT :Microsoft Windows NT
PROD/VER::4.0
OPER/SYS:
KEYWORDS:kberrmsg kbsetup

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft Windows NT Workstation version 4.0 
 - Microsoft Windows NT Server version 4.0 
-------------------------------------------------------------------------------

SYMPTOMS
========

After you install Windows NT 4.0 as an upgrade over an existing installation of
Windows NT 4.0 that had a service pack installed, one or more of the following
errors may occur:

   STOP: 0x0000001E (0xC0000005, 0xFF1BBD79, 0x00000000, 0x00000038)
   KMODE_EXCEPTION_NOT_HANDLED Address ff1bbd79 has base at ff1ae000 - tcpip.sys.

-or-

   STOP 0x00000050 (0xFF10c004, 0x00000000, 0x00000000, 0x00000000)
   PAGE_FAULT_IN_NONPAGED_AREA

NOTE: The first argument may change but the STOP code (0x00000050) is the same.
This may occur either as an in-place upgrade of Windows NT or as an upgrade of
Windows NT Workstation to Windows NT Server.

CAUSE
=====

Windows NT 4.0 was reinstalled as an upgrade over an installation of Windows NT
4.0 that had Service Pack 2 or greater installed and Remote Access Service (RAS)
was installed.

RESOLUTION
==========

For more information on these specific errors and their resolutions, please
reference the following Microsoft Knowledge Base articles:

   ARTICLE-ID: Q162205
   TITLE : "Stop 0x1E" Message Reinstalling Windows NT with SP3 and RAS

   ARTICLE-ID: Q162837
   TITLE : Replacing TCP/IP After SP2 Causes STOP 0x00000050

If you are trying to restore the system to a bootable condition and remove
Service Pack 2, use the following steps:

1. If the partition is formatted as NTFS, install Windows NT to a different
   directory so the files on the partition are accessable.

2. If the partition is formatted as FAT, boot to MS-DOS.

3. Change directories to the Service Pack 2 uninstall directory:

   (%WinRoot%\$NtServicePackUninstall$)

   -or-

   ($NTSER~1 or similar name if under DOS)

4. Copy all the *.sys files in the uninstall directory to the
   %WinRoot%\System32\Drivers of the original Windows NT directory.

5. Copy Win32k.sys from the uninstall directory to%WinRoot%\System32.

6. Copy all other files to %WinRoot%\System32.

7. The system should now be starting correctly. Other errors may be encountered
   at this point, but the system should start.

8. Start the Service Pack 2 update program but select to uninstall the service
   pack. This should bring your system back to a PRE-SP2 configuration.

9. If the service pack was not the source of your original problem, Microsoft
   suggests you re-apply the service pack, but choose NOT to make an uninstall
   directory in order to preserve your original Windows NT system files already
   contained in the previous uninstall directory.

STATUS
======

Installing Windows NT 4.0 as an upgrade over an installation of the same version
is not recommended or supported. If files need to be replaced, boot to MS-DOS if
using a partition formatted as FAT and replace the damaged files, or perform a
new installation of Windows NT to a different directory so a partition formatted
as NTFS can be accessed and then replace the affected files.

An upgrade will attempt to replace files and modify the registry. This may result
in mismatched files and/or corruption to the registry that may leave the system
unbootable. The in-place upgrade does not replace all service pack files, thus
creating an incompatible mix of service pack and non- service pack system
files.


MORE INFORMATION
================

This process will NOT work if Service Pack 2 was installed more than once and
the uninstall option was selected without first uninstalling the service pack,
thus overwriting the uninstall directory. Nor will this work if the uninstall
option was not selected during install of the Service Pack. In this case, a
parallel install of Windows NT will be needed so a tape backup of the original
install can be restored.

Additional query words: sp2 SP 0x1E 0x50 ntfaqset

======================================================================
Keywords          : kberrmsg kbsetup 
Technology        : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT400search kbWinNTSsearch kbWinNTS400search kbWinNTS400
Version           : :4.0
Issue type        : kbprb

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2002.