DOCUMENT:Q162179 10-AUG-2001 [winnt] TITLE :TCP Fast Retransmit and Recovery Added in WinNT 4.0 SP2 PRODUCT :Microsoft Windows NT PROD/VER::4.0 OPER/SYS: KEYWORDS:kbnetwork ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation version 4.0 - Microsoft Windows NT Server version 4.0 ------------------------------------------------------------------------------- IMPORTANT: This article contains information about editing the registry. Before you edit the registry, make sure you understand how to restore it if a problem occurs. For information about how to do this, view the "Restoring Registry Key" Help topic in Regedit.exe or the "Restoring a Registry Key" Help topic in Regedt32.exe. SUMMARY ======= TCP performance on lossy networks has been improved in Windows NT 4.0 Service Pack 2. Support was added for the Van Jacobson TCP fast retransmit and recovery algorithm. MORE INFORMATION ================ For an excellent description of fast retransmit and recovery, see "TCP/IP Illustrated, Volume 1," Richard Stevens, page 312, Addison-Wesley, 1994. A summary of behavior before and after you apply Service Pack 2 is presented. (Assume a receive window size that allows six full-sized Ethernet frames to be sent without waiting for acknowledgment.) Before Service Pack 2 --------------------- Sender Receiver ------------------- packet1 -> packet2 -> <- ack for data up through packet2 packet3 -> (assume this packet is lost) packet4 -> <- ack for data up through packet2 packet5 -> <- ack for data up through packet2 packet6 -> <- ack for data up through packet2 packet7 -> <- ack for data up through packet2 packet8 -> <- ack for data up through packet2 pause, for retransmission timeout of packet 3 data packet3 -> <- ack for data up through packet8 NOTE: After a packet is dropped, the receiver immediately sends an acknowledgment that indicates the receive position in the byte stream each time it receives another packet that is past the hole. These additional ACKS for packet2 are a hint to the sender that there has been a dropped packet. However, prior to Service Pack 2, this indication was not acted on. Instead, the sender continues sending, to the end of the send window, then pauses. Eventually, the retransmission timer for packet3 expires, and it is resent. An ACK is returned for all of the data up through packet8, and the sender starts out again. However, it engages congestion control and starts slowly. As a result, the data throughput is not ideal. The new behavior after applying Service Pack 2 ---------------------------------------------- Sender Receiver ------------------- packet1 -> packet2 -> <- ack for data up through packet2 packet3 -> (assume this packet is lost) packet4 -> <- ack for data up through packet2 packet5 -> <- ack for data up through packet2 packet3 -> (new !!) packet6 -> <- ack for data up through packet6 packet7 -> packet8 -> <- ack for data up through packet8 The new behavior exhibits the fast retransmit and recovery algorithm. On receiving three ACKS for the same sequence number, the sender will quickly retransmit the missing segment, without waiting for the retransmission timer to expire. It also will engage a lesser degree of congestion control, as described in the previously mentioned reference book. WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall your operating system. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk. For information about how to edit the registry, view the "Changing Keys And Values" Help topic in Registry Editor (Regedit.exe) or the "Add and Delete Information in the Registry" and "Edit Registry Data" Help topics in Regedt32.exe. Note that you should back up the registry before you edit it. If you are running Windows NT, you should also update your Emergency Repair Disk (ERD). The following registry parameter can be used to control fast retransmit. To add the registry key: 1. Run Regedt32.exe 2. Go to: HKEY_LOCAL_MACHINE/SYSTEM/currentcontrolset/services/tcpip/parameters 3. Click Edit, click New, and then click Key. Name: TcpMaxDupAcks Value Type: REG_DWORD - Number Valid Range: 1-3 Default: 2 This parameter determines the number of duplicate ACKs that must be received for the same sequence number of sent data before fast retransmit is triggered to resend the segment that has been dropped in transit. Additional query words: semaphore timed out vj twice ====================================================================== Keywords : kbnetwork Technology : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT400search kbWinNTSsearch kbWinNTS400search kbWinNTS400 Version : :4.0 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.