DOCUMENT:Q151376 09-AUG-2001 [winnt] TITLE :How to Disable Autochk if It Stops Responding During Reboot PRODUCT :Microsoft Windows NT PROD/VER:WinNT:3.50,3.51 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation versions 3.5, 3.51, 4.0 - Microsoft Windows NT Server versions 3.5, 3.51, 4.0 ------------------------------------------------------------------------------- SUMMARY ======= When a Windows NT system is shut down improperly or stops responding, Autochk runs against any volumes that are marked as being dirty. If the operating system partition is marked dirty and Autochk tries to repair the volume, and if the damaged volume causes Autochk to stop responding, it is not possible to get back into Windows NT to perform recovery procedures. Additionally, if an extremely large volume becomes corrupt it could take many hours for Autochk to repair the volume (the time required depends on the size of the partition and the number and size of the affected files). In order to get back into Windows NT, you can disable the drive whose partition/volume is causing Autochk to stop responding, then boot into Windows NT and rename Autochk.exe, which is located in the %systemroot%\system32 directory. Once Autochk.exe is renamed so it can't run, you can perform a normal shutdown, re-enable the problem drive whose volume caused Autochk to hang, then reboot the server. Once back in Windows NT, you can perform data recovery procedures by running a manual Chkdsk /F /R or by re-creating the partition and restoring data from a current backup. If the volume/drive causing Autochk to hang cannot be disabled because it is the operating system drive or part of a hardware RAID 5 configuration, it will be necessary to perform the following procedure to replace the Autochk.exe file with a nonexecutable file also called Autochk.exe in order to bypass the Autochk process. MORE INFORMATION ================ WARNING: This procedure should not be performed unless it is impossible to get back into Windows NT any other way in order to perform data recovery procedures. Bypassing the Autochk process simply to save time could cause additional corruption of the partition if you continue to use it without having it repaired by Autochk. To replace the Autochk.exe with a nonexecutable file, perform the following procedure: 1. Modify the contents of the emergency repair disk (ERD) by performing the following steps: a. Find the hidden file called Setup.log on the ERD. b. In Setup.log, find the entry that references autochk.exe in the [files.WinNt] section (Where %systemroot% is your NT installation directory IE: WINNT35). Change the line to the following: \%SystemRoot%\System32\autochk.exe="autochk.exe","99999","\", "ERD disk","autochk.exe" c. While using a text editor such as Notepad, create a file called Autochk.exe, enter any text in the file, then save the file as Autochk.exe in the root directory of the ERD. NOTE: If Running Windows NT V4.0, you must replace the file Setupdd.sys on setup disk #2 with that from Windows NT Service Pack 2 or later. For additional information, please see the following articles in the Microsoft Knowledge Base: Q168015Files Not Replaced When Running Emergency Repair on X86 Intel Q158423WinNT 4.0 ERD Won't Allow Repair w/out Compact Disc Installed 1. Restart your computer with the three Windows NT setup disks. NOTE: If you are running Windows NT 4.0, be sure to copy the Service Pack 3 version of the Setupdd.sys file to the second disk of the three disk installation set. The Setupdd.sys file ensures that the necessary files are actually copied during the ERD process. 2. Choose "R" to repair your Windows NT installation. 3. Select only "Verify Windows NT System Files," then choose Continue. 4. If prompted for "Windows NT Workstation or Server setup disk #4," press the ESC key to allow you to continue with the repair process. 5. DO NOT SELECT TO REPLACE ALL FILES; ONLY REPLACE AUTOCHK.EXE. 6. After Autochk.exe is replaced with the file copied from the repair disk, press F3 to exit the repair process and reboot the computer. Autochk.exe will not run because it was replaced with the text file you created in step 1C above. 7. After performing this process, you will need to make another Emergency Repair Disk by running the RDISK utility. Choose Run from the Start menu, type RDISK and select UPDATE. 8. Replace the Autochk.exe file that is on the system with the one from the Windows NT Installation CD or from the media of the Service Pack currently installed on your system. For additional information about disabling Autochk, see to the following article in the Microsoft Knowledge Base: Q173322How to Disable Autochk During a Windows NT Reboot ====================================================================== Keywords : Technology : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT351search kbWinNT350search kbWinNT400search kbWinNTW350 kbWinNTW350search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS400search kbWinNTS400 kbWinNTS351 kbWinNTS350 kbWinNTS351search kbWinNTS350search Version : WinNT:3.50,3.51 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.