DOCUMENT:Q294818 17-OCT-2001 [sms] TITLE :Frequently Asked Questions About Network Monitor PRODUCT :Microsoft Systems Management Server PROD/VER::2.0,4.0 OPER/SYS: KEYWORDS:kbfaq ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Systems Management Server version 2.0, used with: - the operating system: Microsoft Windows 2000 - the operating system: Microsoft Windows NT 4.0 ------------------------------------------------------------------------------- SUMMARY ======= This article answers frequently asked questions about Network Monitor. MORE INFORMATION ================ Introduction: Network Monitor is a utility that comes with Microsoft Systems Management Server and Microsoft Windows 2000 Server. You can use Network Monitor (also known as NetMon) to capture and observe network traffic patterns and problems. Capture Window When you first start Network Monitor, it displays the Capture window. The Capture window includes four frames: +-----------------------------------------------------------------------------------------------------------------------+ | Pane Name | Contents | +-----------------------------------------------------------------------------------------------------------------------+ | Graph | Graphical representation of current network activity | +-----------------------------------------------------------------------------------------------------------------------+ | Session Statistics | Statistics about current individual network sessions | +-----------------------------------------------------------------------------------------------------------------------+ | Station Statistics | Statistics about sessions sent to or from the computer that is running Network Monitor | +-----------------------------------------------------------------------------------------------------------------------+ | Total Statistics | Summary statistics about network activity that has been detected since the capture process began | +-----------------------------------------------------------------------------------------------------------------------+ Frame Viewer Window After a Network Monitor trace has been captured, you can view it from within Network Monitor immediately through the Frame Viewer window, or you can save it to a file for analysis later. Data in the Frame Viewer window is presented in three frames, which allow you to view the captured data in varying degrees of detail: +--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Pane Name | Contents | +--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Summary | Lists the frames for the captured data in the order in which they were captured, including the time the frame arrived, the source and destination media access control addresses, protocol, a summary description, and the other Source/Destination addresses (for example, IP addresses). | +--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Detail | Parses each frame and breaks out protocol information. To display the protocol's property data, click to expand a field in the Detail pane. If you select a line in the detail pane, the associated hexadecimal data is highlighted in the Hex pane. | +--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Hex | Displays the content of the selected frame, both in hexadecimal and ASCII format. | +--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ Questions and Answers: 1. Q. Where do I get the Network Monitor tool? A. There are two versions of Network Monitor. The full version is shipped with Microsoft Systems Management Server (SMS). A "lite" version is included with Windows NT Server and Windows 2000 Server and contains a subset of the features that are available in the full version. 2. Q. Which version should I use? A. It depends on what kind of traffic you need to capture. Both versions of Network Monitor can capture traffic that is sent to or from the host computer (the computer that is running NetMon), including broadcasts and traffic over a dial-up network connection. The full version of Network Monitor also allows you to capture and display any frames from the network segment on which the computer that is running NetMon resides, regardless of whether they are addressed to the host computer. 3. Q. What is the difference between the Network Monitor Agent and Network Monitor Tools and Agent? A. The two primary components of Network Monitor are the Network Monitor Agent and the user interface. The Network Monitor Agent monitors the network and passes traffic up to the "program" (the user interface). The Network Monitor Agent can run on any compatible computer while the program is running on a separate computer. A computer can only see network traffic that passes across its network segment. Thus, it can be helpful to have a Network Monitor Agent that is running on a network where the problem is occurring, while the Network Monitor user interface runs from (for example) the local area network (LAN) Administrator's computer on a different network segment. The LAN Administrator can then manage the capture and view the captured data from his or her computer, even though the LAN Administrator is not on the segment where the problem is occurring. 4. Q. What security risks are introduced by the use of Network Monitor? A. Network Monitor is a "sniffer," namely, it detects problems on the network. Because you can analyze traffic at the frame level, all non-encrypted data is visible in a trace. For example, when you use Microsoft Internet Information Server (IIS) with Basic Authentication, the password is passed as clear text and can be read in a Network Monitor trace. 5. Q. What is the difference between a media access control address and an IP address? How can I distinguish one from another? A. A media access control (MAC) address is a unique, 12-digit (48-bit), hexadecimal number that the network interface card (NIC) manufacturer "burns into" a computer's network interface card. On some cards, software can override this number, but the number remains burned into the card. MAC addresses are also referred to as "Hardware Addresses" and "Universally Administered Addresses" (UAAs). When they are overridden, MAC addresses are called "Locally Administered Addresses" (LAAs). The media access control is the lowest layer of the network model that contains address information. All frames on a local area network contain a MAC address, regardless of the network protocol in the frame. The same cannot be said about Internet Protocol (IP) addresses, which reside at a higher level of the network model. Non-IP traffic, such as traffic that uses the Novell IPX/SPX protocol, have a MAC address but not an IP address. An IP address is a 32-bit address that should be unique across a Transmission Control Protocol/Internet Protocol (TCP/IP) network. IP addresses are usually represented in dotted-decimal notation, which depicts each octet (eight bits) of an IP address as its decimal value and separates each octet with a period (for example, 172.16.255.255). When you view captured data in Network Monitor, you can set up a friendly name for either type of address. To do this, right-click the address in the Summary pane of the Frame Viewer window, and then click Edit Address. 6. Q. What if the network adapter card does not support promiscuous mode? What is promiscuous mode anyway? A. Promiscuous mode is a state in which a network adapter card copies all the frames that pass over the network to a local buffer, regardless of the destination address. This mode enables Network Monitor to capture and display all network traffic. To use Network Monitor, your computer must have a network card that supports promiscuous mode. If you are using Network Monitor Agent on a remote computer, the local workstation does not need a network adapter card that supports promiscuous mode, but the remote computer does. 7. Q. How does Network Monitor interpret the protocols in a trace that has been captured? A. Network Monitor includes protocol parsers that look at and interpret key items within the raw data to interpret some of the most common protocols. As new standards and implementations evolve, there will be certain protocols for which NetMon does not contain parsers. Individuals can write parsers for these protocols, or other companies may write some of these parsers (which can be found on the Internet). Some additional parsers are included in the Microsoft Resource kits. 8. Q. Why can't I see HTTP activity, but I can see my calls under a different protocol? A. The Network Monitor HTTP parser looks for TCP port 80 to identify a frame as an HTTP frame. If the Web site uses a different port than the standard Port 80 (0x50), the parser does not recognize that the frame contains HTTP data. In the Web Site Properties, on the Web Site tab, check your IIS configuration to see if the TCP Port 80 is designated. 9. Q. What is a three-way handshake? A. Before any data can be transmitted through the TCP protocol, a reliable connection must be established. A "three-way handshake" is the process that TCP uses to establish this connection. This process cannot be thoroughly described within the context of this article. Briefly, three frames identify a three-way handshake. In the first frame, Computer1 sends a frame to Computer2 with the TCP SYN flag set. In the second frame, Computer2 sends a frame back to Computer1 with both the SYN and ACK flags set. In the third frame, Computer1 sends a frame to Computer2 with the ACK flag set. Any two computers exchange these three packets every time they set up a TCP connection. 10. Q. How does a disconnect appear in a NetMon trace? A. A TCP connection can be ended in one of two ways. A "graceful" close uses the TCP FIN flag to show that the sender has no more data to send. The TCP RST flag is used for an ended ("abortive") session disconnection. 11. Q. What is the difference between a Capture filter and a Display filter? A. Before you run the Capture, you can set up a Capture filter to determine which frames are stored in the buffer. After the data is stored, you can set up a Display filter to further focus attention on a particular set of frames. 12. Q. Can Capture and Display filters be saved as the default? A. To save a Capture or Display filter as the default, you must write over the existing file. The default Display filter file is named Default.df, and the default Capture filter file is named Default.cf. These files are usually located in the WinNT/System32/Netmon/Captures/ folder. Alternatively, you can save and load various filter files as needed from within Network Monitor. To do this, click Load on the Capture Filter or Display Filter dialog box. 13. Q. I have received the Capture. How do I make it more readable? A. You cannot sort the frames, but you can sort the appearance of the Summary pane. To do this, drag the column names to the preferred order. Also, you can replace an address with a meaningful name. To do this, right-click the address in the Summary pane of the Frame Viewer window, and then click Edit Address. 14. Q. Should I run Network Monitor on the client, the server, or both? What if the client and server are the same computer? A. Usually, when client and server applications are on the same computer, there is no network traffic. Thus, you cannot use Network Monitor to understand what is happening between the applications. When you are troubleshooting HTTP or other text-based protocols, if you have two computers, and the client is getting back unexpected results, run Network Monitor on the server to see if the server is sending the correct data. You may need to trace on both the client and server if a firewall or intranet is causing network problems. In this scenario, you can compare traces more efficiently if you use the Net Time command to synchronize the system time on the computers. If you have three computers that communicate in a three-tier architecture, you can run Network Monitor on the middle tier because all traffic crosses that computer. 15. Q. Can the user run other applications while Network Monitor is capturing or filtering the network traffic? A. Yes, the overhead of NetMon is minimal, and other applications should not be impacted by Network Monitor. REFERENCES ========== For additional information, click the article numbers below to view the articles in the Microsoft Knowledge Base: Q169292 The Basics of Reading TCP/IP Traces Q231920 How to Filter on TCP Header Information Using Microsoft Network Monitor Q232247 Using Network Monitor to Capture Traffic Using a Remote Agent Q172983 Explanation of the Three-Way Handshake via TCP/IP Additional query words: ====================================================================== Keywords : kbfaq Technology : kbSMSSearch Version : :2.0,4.0 Issue type : kbinfo ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.