DOCUMENT:Q178278 09-AUG-2001 [winnt] TITLE :Boot Partition Using CPQArray has Limits if Using scsi() Syntax PRODUCT :Microsoft Windows NT PROD/VER:WinNT:3.51,4.0 OPER/SYS: KEYWORDS:kbhw kbHardware ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation versions 3.51, 4.0 - Microsoft Windows NT Server versions 3.51, 4.0 ------------------------------------------------------------------------------- SYMPTOMS ======== If you attempt to install Windows NT using a Compaq Array controller whose BIOS is disabled or to a boot partition that extends beyond 1024 cylinders, you may see one of the following errors after the text mode portion of setup reboots: (NOTE: The type of error depends on if you are using a PCI Based Compaq Smart-2/P Array controller or an EISA based Compaq Smart-2/E Array controller) If you are using a Compaq Smart-2/P Array controller (PCI based) or Fast and Wide-2 controller: The system did not load because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check the boot path and disk hardware. Please check the Windows NT documentation about hardware disk configuration and your hardware reference manuals for additional information. Boot failed. -or- boot signature aa55 not found error -or- If you are using a Compaq Smart-2/E Array controller (EISA based): TRAP 0000000E ============ PAGE FAULT ============= ** at linear address 00000002 tr=0028 cr0=80000011 cr2=00000002 cr3=00300000 . . . CAUSE ===== If the boot partition extends beyond 1,024 cylinders or the boot partition is created on a drive attached to a SCSI controller whose BIOS is disabled, use the scsi() syntax in the Boot.ini file. The scsi() syntax is not supported while using a Compaq Smart 2/P Array controller. -or- The Cpqarray.sys driver that ships with Windows NT does not support using the scsi() syntax for addressing a Compaq Smart 2/E Array controller. RESOLUTION ========== 1. Install Windows NT to a boot partition that does not extend beyond the 1,024 cylinder limitation of Interrupt 13 BIOS calls. 2. Use an updated Cpqarray.sys driver for Ntbootdd.sys when using scsi() syntax in the Boot.ini file and an EISA based Compaq Smart-2/E Array controller. 3. Use a different SCSI Controller and driver that supports booting from a boot partition that extends beyond 1,024 cylinders. 4. Contact Compaq Technical Support about this limitation when using scsi() syntax with the PCI based Compaq Smart-2/P Raid Controller. STATUS ====== The products discussed here are manufactured by Compaq Corporation, A vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding the products' performance or reliability. MORE INFORMATION ================ Interrupt 13 compatibility is required so the master boot record (MBR) can locate the boot sector. The boot sector then finds and loads the NT boot loader (NTLDR) and continues to load the operating system. NT uses interrupt 13 calls until a disk driver is loaded. If the boot partition can be accessed with Interrupt 13 BIOS calls then Windows NT will use the multi() syntax which does not load a driver for the disk controller until the Operating System starts loading from this partition. When using the scsi() syntax in the BOOT.INI, Windows NT needs to load a SCSI device driver and uses that driver to access the boot partition. The SCSI controller driver is renamed NTBOOTDD.SYS and placed in the root of the system partition. Two reasons for using scsi() syntax in the c:\boot.ini file: - The BIOS is disabled on the disk controller that Windows NT is installed on, so Interrupt 13 Bios calls cannot be used. - The boot partition extends beyond the 1024th cylinder on the drive which is a limitation of Interrupt 13 BIOS calls. For more information about ARC Path Names, see NT 4.0 Server Resource Guide or NT 4.0 Workstation Resource Kit or refer to the following article in the Microsoft Knowledge Base. ARTICLE ID: Q102873 TITLE : BOOT.INI and ARC Path Naming Conventions and Usage. ARTICLE ID: Q114841 TITLE : Windows NT Boot Process and Hard Disk Constraints Additional query words: Smart raid Array 2E 2P cpqfs.sys ====================================================================== Keywords : kbhw kbHardware Technology : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT351search kbWinNT400search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS400search kbWinNTS400 kbWinNTS351 kbWinNTS351search Version : WinNT:3.51,4.0 Issue type : kbprb ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.