DOCUMENT:Q172952 09-AUG-2001 [winnt] TITLE :How to Rebuild Corrupted or Missing SYSTEM Partition PRODUCT :Microsoft Windows NT PROD/VER:WinNT:3.51,4.0 OPER/SYS: KEYWORDS:kbsetup ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation versions 3.51, 4.0 - Microsoft Windows NT Server versions 3.51, 4.0 ------------------------------------------------------------------------------- SUMMARY ======= Digital Equipment Corporation (DEC) ALPHA-based RISC computers rely on a small (less than 4 GB) FAT-formatted SYSTEM partition containing boot files. This SYSTEM partition can also contain the Windows NT operating system, but must be FAT. RISC computers use the system's firmware and the ARC paths defined in NVRAM to read the SYSTEM and OSLOAD partitions. The firmware loads boot files from the SYSTEM partition; the SYSTEM partition loads the Windows NT operating system files from the OSLOAD partition. If the SYSTEM partition is damaged, corrupted, or deleted, the system will no longer start. The SYSTEM partition can have any partition number, but is usually Partition-1. Typical Disk Configuration -------------------------- _________<4GB______________________________________________ | SYSTEM PARTITION - FAT | BOOT PARTITION - NTFS or FAT | | | | | \Os\Winntxx\Osloader.exe | \Winnt\System32\Ntoskrnl.exe | | \Hal.dll | | | \*.PAL files | | |__________________________|________________________________| SYSTEMPARTITION (1) OSLOADPARTITION (2) The SYSTEM partition contains Os\Winntxx directory (xx = Windows NT OS version). The OSLOAD partition contains the Winnt directory or a user- defined directory for Windows NT. Until the SYSTEM partition can be rebuilt, use the article below to help return to Windows NT: Q172806 Creating an NT Boot Floppy for DEC ALPHA RISC Machines After you are in Windows NT, you can try to run Chkdsk.exe to recover the partition. If Disk Administrator shows the small SYSTEM partition as unknown, Windows NT 3.51 will allow you to reformat or delete and recreate the SYSTEM partition. Disk Administrator in Windows NT 4.0 will not allow you to delete or reformat the SYSTEM partition. If you try to do so, you will receive one of the following messages: Windows NT cannot format a volume containing Windows NT system files -or- Disk Administrator cannot delete the active partition on disk 0 MORE INFORMATION ================ To rebuild the SYSTEM partition, you must either run a built-in program contained in the ALPHA firmware or use a utility called Arcinst.exe from the Windows NT installation compact disc's Alpha directory to delete and then create the SYSTEM partition. DEC has two different kinds of firmware: the new AlphaBios firmware and the original ARC MULTIBOOT firmware. Depending on the model number and age of the computer, either kind of firmware could be in place. NOTE: The screens and menu items may vary from one firmware revision to the next. Use the appropriate section below for instructions on deleting or creating a new SYSTEM partition. Deleting and Creating a SYSTEM Partition Using AlphaBios Firmware ----------------------------------------------------------------- To delete a system partition and then create a new one, use the following steps: 1. Turn on power to the system. 2. After POST initialization completes, press F2 to enter SETUP; the menu will look similar to the following: Display System Configuration Upgrade AlphaBios Hard Disk Setup ... CMOS Setup ... Install Windows NT Utilities About AlphaBios 3. From the AlphaBios SETUP menu, click Hard Disk Setup. 4. A map of the drives and partitions will be displayed along with selections for deleting and creating or formatting partitions. The map will resemble the following diagram: ----------------------------------------------------------- Disk 0 QLISP10x0 SCSI ID 0 4091MB Partition 1 4081MB FAT Partition 2 10MB UNKNOWN Insert=NEW DEL=Delete F6=Format F7=Express Esc=Exit ----------------------------------------------------------- 5. Select the damaged SYSTEM partition, and then either press F6 to format, or choose DELETE and then create a new partition and format it. NOTE: If you are recovering a Windows NT 3.51 installation, it will be necessary to start Windows NT using the boot floppy as described in the following Knowledge Base article: Q172806 Creating a WinNT Boot Floppy for DEC ALPHA RISC Computers This is necessary because the Windows NT repair process fails to copy the Windows NT loader files if the Os\Winnt351 directory structure is not found on the newly-created partition. After you manually recreate this directory structure on the SYSTEM partition, copy the six boot files manually from the Windows NT installation compact disc, or perform a normal shutdown and then continue with step 5 from within the AlphaBios SETUP menu. 6. Go back to the main menu, and then click Install Windows NT. 7. At the first Windows NT Setup screen, press R to repair. 8. When you see the following menu, select only this repair option: [ ] Inspect registry files [ ] Inspect startup environment [x] Verify Windows NT system files. By selecting this option, Windows NT 4.0 setup will recreate the Os\Winnt40 directory structure on the newly created SYSTEM partition, and then prompt to replace the following files from the Windows NT installation compact disc: - A221064.PAL - A221066.PAL - A221164.PAL - A321064.PAL - Osloader.exe - Hal.dll NOTE: If you have any Windows NT service packs installed, it is very important that you only allow Windows NT to replace the above six files, then select F3 to exit repair after they have been replaced. Do NOT select A to replace all files during Repair. 9. After repair is complete, restart the system. The system should start up using the re-created SYSTEM partition. Deleting and Creating a SYSTEM Partition Using ARC Multiboot Firmware --------------------------------------------------------------------- 1. Insert the Windows NT installation compact disc into the CD-ROM drive. 2. Start the system. The first menu will be the Boot menu, which will appear similar to the following: Boot menu: Boot Windows NT Server Vx.xx Boot an alternate Operating System Run A Program Supplementary menu... 3. Click Run a Program on the menu. Type the following path, and then press ENTER: cd:\alpha\arcinst Arcinst.exe will load from the compact disc and give you the following choices: CONFIGURE PARTITIONS EXIT Click Configure Partitions. Next, you will see this menu: CREATE SYSTEM PARTITION DELETE PARTITION MAKE EXISTING PARTITION INTO THE SYSTEM PARTITION EXIT Click Delete Partition, and then select the small ~4 MB FAT partition. Click Create a New System partition; the program will prompt you to enter the size of the new partition: ENTER SIZE IN MB (1-4) After the partition is made, it will be automatically formatted. 4. Exit Arcinst.exe and go back to the main Boot menu. NOTE: If you are recovering a Windows NT 3.51 installation, it will be necessary to start Windows NT using the boot floppy as described in the following Knowledge Base article: Q172806 Creating a WinNT Boot Floppy for DEC ALPHA RISC Computers This is necessary because the Windows NT repair process fails to copy the Windows NT loader files if the Os\Winnt351 directory structure is not found on the newly-created partition. After you manually recreate this directory structure on the SYSTEM partition, copy the six boot files manually from the Windows NT installation compact disc, or perform a normal shutdown and then continue with step 5 from within the ARC Multiboot menu. 5. Select Run a Program from the main Boot menu. Type the following path, then press ENTER: cd:\alpha\setupldr 6. At the first Windows NT Setup screen, press R to repair. 7. When you see the following menu, select only this repair option: [ ] Inspect registry Files [ ] Inspect startup environment [x] Verify Windows NT system files. When you select this option, Windows NT 4.0 setup will recreate the directory structure os\winnt40 on the newly-created SYSTEM partition, then prompt you to replace the following files from the Windows NT Installation CD-ROM: - A221064.PAL - A221066.PAL - A221164.PAL - A321064.PAL - Osloader.exe - Hal.dll NOTE: If you have any Windows NT service packs installed, it is very important that you only allow Windows NT to replace the above six files, then select F3 to exit repair after they have been replaced. Do NOT select A (replace all files) during Repair. 8. After Repair is complete, restart the system. The system should boot using the re-created system partition. Additional query words: RISC ALPHA BOOT SYSTEM ====================================================================== Keywords : kbsetup Technology : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT351search kbWinNT400search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS400search kbWinNTS400 kbWinNTS351 kbWinNTS351search Version : WinNT:3.51,4.0 Hardware : ALPHA Issue type : kbhowto ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.