DOCUMENT:Q132554  08-AUG-2001  [winnt]
TITLE   :Micro Channel Digiboard PC/XEM Fails Under Windows NT
PRODUCT :Microsoft Windows NT
PROD/VER::3.5 SP2,3.51
OPER/SYS:
KEYWORDS:

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft Windows NT Workstation versions 3.5 SP2, 3.51 
 - Microsoft Windows NT Server versions 3.5 SP2, 3.51 
-------------------------------------------------------------------------------

SYMPTOMS
========

After you install Windows NT 3.5 Server Pack 2 or Windows NT 3.51, your
asynchronous Digiboard PC/XEM micro channel adapter stops working. The following
messages are written to the event log:

   Source: SCM
   Event ID: 7000
   Description: Digi fep 5 driver service failed to start due to the following
   error:

   No mapping between account names and security id's was done.

   Source: DIGIFEP5
   Event ID: 5
   Description: The description for event id %5% in source digifep5 could not be
   located. It contains the following insertion string(s),NTXEM2.

CAUSE
=====

Windows NT does not correctly save the slot number in the registry on MCA
computers. The slot number is incorrectly saved as 0.

Also, the Digiboard driver downloads its configuration information to the board
during initialization. If the computer is not cold booted (turned off) between
configuration changes, the driver will not reinitialize the board on the next
boot.

WORKAROUND
==========

To work around this problem, run Registry Editor (REGEDT32.EXE) and modify the
following key in the HKEY_LOCAL_MACHINE hive to manually change the slot
number:

   \System\CurrentControlSet\Services\NTXEM2\Parameters\Slot Number

WARNING: Using Registry Editor incorrectly can cause serious, system-wide
problems that may require you to reinstall Windows NT to correct them. Microsoft
cannot guarantee that any problems resulting from the use of Registry Editor can
be solved. Use this tool at your own risk.

1. If you have already installed the Digiboard driver, unistall it and reboot
   (cold boot) the computer.

2. Use the Microchannel Reference floppy disk that was supplied with the
   computer to confirm that the Digiboard has been configured properly and the
   reboot (cold boot) the computer.

3. Boot Windows NT and install the Digiboard driver. Do not reboot the computer.

4. Run Registry Editor (REGEDT32.EXE).

5. From the HKEY_LOCAL_MACHINE subtree, go to the following key:

 
      SYSTEM\CurrentControlSet\Services\NTXALL[1-n]\Parameters
 

6. Change the value for SlotNumber to the correct slot number.

7. Run Control Panel, choose Network, and configure the Digiboard. The correct
   slot number will appear and Setup will reconfigure the other values
   correctly. Quit Control Panel, but choose not to reboot the computer.

8. Shutdown the computer and then reboot (cold boot) it again:

   a. From the Program Manager File menu choose Shutdown.

   b. Choose Shutdown and then choose OK.

   This allows any configuration currently saved in the Digiboard to be cleared,
   allowing Windows NT to reinitialize it during the next boot process.


STATUS
======

Microsoft has confirmed this to be a problem in Windows NT version 3.5 SP2 and
3.51. We are researching this problem and will post new information here in the
Microsoft Knowledge Base as it becomes available.

Additional query words: 3.50 3.51 prodnt ras zero micro channel

======================================================================
Keywords          :  
Technology        : kbWinNTsearch kbWinNTWsearch kbWinNT351search kbWinNT350search kbWinNTW350search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS351 kbWinNTS351search kbWinNTS350search kbWinNTW350SP2 kbWinNTS350SP2
Version           : :3.5 SP2,3.51

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2001.