|
|
HP Services Software Patches - cscpat_2042010
|
Copyright (c) Digital Equipment Corporation 1994, 1995. All rights reserved
PRODUCT: DEC Open3D V2.2 for OpenVMS AXP
OP/SYS: OpenVMS Alpha
SOURCE: Digital Equipment Corporation
NOTE: The image PCM$SERVER contained in this ECO was incorrectly
linked against OpenVMS AXP V6.1. Therefore, the following
error will be returned when a "RUN PCM$SERVER" is
executed.
%DCL-W-ACTIMAGE, error activating image LIBOTS
-CLI-E-IMGNAME, image file
SCRLET$DKA300:[SYS0.SYSCOMMON.][SYSLIB]LIBOTS.EXE
-SYSTEM-F-SHRIDMISMAT, ident mismatch with shareable image
To workaround this problem,
o the PCM subset should NOT be selected when this ECO is
installed
or
o after installing this ECO, the newly installed
SYS$SYSTEM:PCM$SERVER image should be deleted.
The image from the original DEC Open3D V2.2 for DEC
OpenVMS AXP product should be used.
ECO INFORMATION:
CSCPAT Kit: CSCPAT_2042 V1.0 (CSCPAT_2042010)
CSCPAT Kit Size: CSCPAT_2042010.A;1 666
CSCPAT_2042010.B;1 468
CSCPAT_2042010.C;1 7164
CSCPAT_2042010.D;1 10026
CSCPAT_2042010.E;1 9090
CSCPAT_2042010.F;1 720
CSCPAT_2042010.G;1 90
CSCPAT_2042010.H;1 2250
CSCPAT_2042010.I;1 1332
CSCPAT_2042010.J;1 3258
CSCPAT_2042010.K;1 1962
CSCPAT_2042010.L;1 4662
Total of 12 files, 41688 blocks.
Engineering Cross Reference: OPEN3D_EO7022
Kit Applies To: OpenVMS Alpha V1.5, V1.5-1H1
DEC Open3D V2.2 for DEC OpenVMS AXP
NOTE: OpenVMS Alpha V1.5-1H1 is only required
for the use of the ZLX graphic
accelerators. If you have a PXG graphics
accelerator or an HX board, then the kit
can be installed on OpenVMS AXP V1.5.
System Reboot Necessary: If the system is a Workstation with
a 3D graphics card installed, it will
need to be rebooted. Otherwise, it
will not.
NOTE: In addition to the problems described below, other minor
problems have been corrected with this kit. All systems
running DEC Open3D V2.2 be should be updated with this
ECO kit.
For more information describing this ECO kit, please see
the OPEN3D022.RELEASE_NOTES contained in the kit.
ECO KIT SUMMARY:
An ECO kit exists for DEC Open3D V2.2 on OpenVMS Alpha V1.5 through
V1.5-1H1. This kit addresses the following problems:
o Server crash on end-session on ZLX-E1 on DEC 3000 Model 300
and DEC 3000 Model 500.
o On systems with ZLX-M graphics options, windows with large
negative coordinates were being incorrectly mapped. This
resulted in some application programs' icons not being
displayed correctly.
INSTALLATION NOTES:
If the system is a Workstation with a 3D graphics card, the system will
need to be rebooted. Otherwise, the system does not need to be rebooted,
but the DECwindows server must be started with the following command:
@SYS$STARTUP:DECW$STARTUP RESTART
Files on this server are as follows:
|
»cscpat_2042010.README
»cscpat_2042010.CHKSUM
»cscpat_2042010.a-dcx_axpexe
»cscpat_2042010.b-dcx_axpexe
»cscpat_2042010.c-dcx_axpexe
»cscpat_2042010.d-dcx_axpexe
»cscpat_2042010.e-dcx_axpexe
»cscpat_2042010.f-dcx_axpexe
»cscpat_2042010.g-dcx_axpexe
»cscpat_2042010.h-dcx_axpexe
»cscpat_2042010.i-dcx_axpexe
»cscpat_2042010.j-dcx_axpexe
»cscpat_2042010.k-dcx_axpexe
»cscpat_2042010.l-dcx_axpexe
|