 |
Index for
Section 8 |
|
 |
Alphabetical
listing for H |
|
 |
Bottom of
page |
|
hwmgr_view(8)
NAME
hwmgr_view - Displays information about the status of the system and its
hardware components
SYNOPSIS
/sbin/hwmgr view cluster
/sbin/hwmgr view devices [-dsf device-special-filename] [-category
hardware-category] [-member cluster-member-name] [-cluster]
/sbin/hwmgr view environment
/sbin/hwmgr view hierarchy [-id hardware-component-id [-instance
component-instance]] [-member cluster-member-name]
/sbin/hwmgr view timestamps [-reverse] [-a timestamp-attribute...] [-a
timestamp-attribute=time] [-id hardware-component-id] [-category hardware-
category] [-member cluster-member-name] [-cluster]
/sbin/hwmgr view transaction [-member cluster-member-name] [-cluster]
OPTIONS
The following options are available:
view cluster
Displays information about the state of each cluster member. This
command is useful only in a cluster environment.
view devices
Displays all devices. All devices on the local host are returned by
default, unless you also specify one of the following options:
-category hardware-category
Specifies a hardware category, such as disk or tape on which to
perform the operation. Use the hwmgr get category command option to
display a list of available category names.
-dsf device-special-filename
Specifies the device special file for a particular device. You can
obtain the device special file name by using the hwmgr show
component -full command option (see the DSF GROUP) or the hwmgr
show scsi command option.
-cluster
Specifies that the operation be performed clusterwide. If this
option is not specified, data for the local host is returned.
-member cluster-member-name
Specifies the host name of a cluster member on which to perform the
operation.
For the purpose of this command, a device is considered to be any
hardware component that has the dev_base_name attribute. (Otherwise,
the documentation uses the generic term component to refer to
individual items of hardware such as a network card.)
view env
Displays the internal hwmgr environment variable settings, which you
can set in your environment configuration file such as your .profile
file. Refer to hwmgr(8) for more information.
view hierarchy
Displays the hierarchical relationship of all hardware components. Each
component is displayed with its descendent components. For example,
this option displays SCSI buses with all the SCSI devices attached to
each bus. If you do not specify a cluster member name, this operation
defaults to the local system.
-id hardware-component-ID
Displays a specific component and all its descendents. Specify a
hardware identifier (HWID).
-inst component-instance
Specifies an instance of a hardware component. Some components
might be in the hierarchy in more than one place. For example,
SCSI disks on a shared bus might be seen in the hierarchy under two
or more buses. Each entry for the component in the hierarchy is
considered a different instance.
You must specify the -id option when using the -inst option.
-member cluster-member-name
Specifies the host name of a cluster member on which to perform the
operation.
Use the hwmgr view hierarchy command to display the currently
registered hardware components that are found in the system hierarchy.
Components that have a flagged status are identified in the command
output by the following codes:
· (!) warning
· (X) critical
· (-) inactive
Refer to the description of the hwmgr status component command for an
explanation of these codes in hwmgr_ops(8). See the Managing Online
Addition and Removal manual for procedures to correct a component
problem.
view timestamps
Displays time stamp attributes for components, such as their
registration time or the time that the most recent event was posted.
The timestamp attributes are displayed in chronological order. You can
specify the following additional options:
-reverse
Specifies that you want to display the data in reverse
chronological order.
-a timestamp-attribute
Specifies that you want to display only timestamps that have the
stated attribute. Examples of valid attributes are:
registration_time, start_stop_time, and last_event_time. For
example:
# hwmgr view timestamp -a registration_time
-a timestamp-attribute="time"
Specifies that you want to find a specific attribute and value
pair. Examples of valid attributes are: registration_time,
start_stop_time, and last_event_time. An example of the syntax
follows:
# hwmgr view timestamp -a registration_time="Thu Jun 20 16:00:28 2002"
You must specify the full time string of day, date, time, and year.
-id hardware-component-id
Specifies that you want to display timestamps for a particular
component. You must supply a HWID for the component, which you
obtain by using the hwmgr show component command.
-category hardware-category
Specifies that you want to display timestamps for a particular
category of component. You can obtain a list of categories that are
available on the system by using the hwmgr get category command.
-member cluster-member-name
Specifies the cluster member on which you want to perform the
operation.
-cluster
Specifies that you want to perform the operation on all members of
the cluster.
view transaction
Displays information about the transactions that the hardware
management kernel code uses to perform some requests, including the
status of:
· The current hardware management transactions, if any.
· The last hardware management transaction that was completed.
· All requests for the various transactions.
You can specify the following additional options:
-member cluster-member-name
Specifies the cluster member on which you want to perform the
operation.
-cluster
Specifies that you want to perform the operation on all members of the
cluster.
DESCRIPTION
The commands described in this reference page are a subset of the options
that you can use with the hwmgr command. See hwmgr(8) for an overview of
the commands.
Use the hwmgr view command option to display information about the status
of the system and its hardware components. Each view command provides
different output about the components that you specify. Enter the view
command that best fits your need. Refer to the following pages for
information on related commands:
· hwmgr_show(8) - Describes commands that enable you to display
information from hardware subsystems.
· hwmgr_get(8) - Describes commands that enable you to display (get) or
configure (set) component attributes and identify component category
names.
· hwmgr_ops(8) - Describes commands that enable you to perform
administrative tasks on hardware components, such as scanning buses,
locating components, powering off components, and deleting components.
See the Hardware Management manual for more information about components,
device special files, and a definitive list of the supported device names.
This manual provides further examples of hwmgr command usage and common
procedures.
You can run some hwmgr commands directly from the SysMan Menu. You can also
monitor many properties and attributes of components by using the SysMan
Station GUI. See the System Administration manual for information about
these interfaces.
RESTRICTIONS
The following notes and restrictions apply:
When working on a cluster, if you do not specify a member name the
operation defaults to the local member. Some command options might require
that you specify a member name, but in general it is an option.
ERRORS
The command returns an int with an errorno from <errno.h>.
EXAMPLES
These examples have been reformatted for ease of reference. The actual
formatted output from commands might be slightly different.
1. If your system is a member of a cluster, use the hwmgr command to send
hardware management requests to any node in the cluster. Use the
following command to determine the current state of each member of the
cluster:
# /sbin/hwmgr view cluster
Member ID State Member HostName
--------- ----- ---------------
1 UP rene (localhost)
31 UP witt
24 UP freu
10 UP rogr
2. The following example displays devices (components that have a
dev_base_name attribute) that are connected to the system:
# /sbin/hwmgr view devices
# hwmgr view devices
HWID: Device Name Mfg Model Location
----------------------------------------------------------------------
3: /dev/dmapi/dmapi
4: /dev/scp_scsi
5: /dev/kevm
58: /dev/disk/dsk0c COMPAQ BD0366459B bus-0-targ-0-lun-0
59: /dev/disk/dsk1c COMPAQ BD0366459B bus-0-targ-1-lun-0
60: /dev/disk/cdrom0c COMPAQ CD-224E bus-1-targ-0-lun-0
61: /dev/ntape/tape0 COMPAQ SDT-10000 bus-5-targ-0-lun-0
66: /dev/disk/floppy0c 3.5in floppy fdi0-unit-0
68: /dev/random
69: /dev/urandom
The information shown in the output is as follows:
HWID
The cluster-wide unique hardware identifier (integer) assigned to
the device
Device Name
The device special file name for the device
Mfg The manufacturer of the device, if provided
Model
The vendor's model number, as shown on the device or its enclosure
Location
The physical location of the device as defined by the operating
system
In the preceding example, no tape device is present and the following
command displays no information:
# /sbin/hwmgr view devices -cat tape
3. The following example displays all devices on a cluster:
# /sbin/hwmgr view devices -cluster
HWID: Device Name Mfg Model Host Location
--------------------------------------------------------
3: /dev/kevm jully
28: /dev/disk/floppy0c 3.5in floppy jully fdi0-unit-0
40: /dev/disk/dsk0c DEC RZ28M (C)DEC jully bus-0-targ-0-lun-0
41: /dev/disk/dsk1c DEC RZ28L-AS (C)DEC jully bus-0-targ-1-lun-0
42: /dev/disk/dsk2c DEC RZ28 (C)DEC jully bus-0-targ-2-lun-0
43: /dev/disk/cdrom0c DEC RRD46 (C)DEC jully bus-0-targ-6-lun-0
44: /dev/disk/dsk3c DEC RZ28M (C)DEC phoey bus-1-targ-1-lun-0
45: /dev/disk/dsk4c DEC RZ28L-AS (C)DEC jully bus-1-targ-2-lun-0
45: /dev/disk/dsk4c DEC RZ28L-AS (C)DEC phoey bus-1-targ-2-lun-0
46: /dev/disk/dsk5c DEC RZ29B (C)DEC jully bus-1-targ-3-lun-0
46: /dev/disk/dsk5c DEC RZ29B (C)DEC phoey bus-1-targ-3-lun-0
47: /dev/disk/dsk6c DEC RZ28D (C)DEC jully bus-1-targ-4-lun-0
47: /dev/disk/dsk6c DEC RZ28D (C)DEC phoey bus-1-targ-4-lun-0
48: /dev/disk/dsk7c DEC RZ28L-AS (C)DEC jully bus-1-targ-5-lun-0
48: /dev/disk/dsk7c DEC RZ28L-AS (C)DEC phoey bus-1-targ-5-lun-0
49: /dev/disk/dsk8c DEC RZ1CF-CF (C)DEC jully bus-1-targ-8-lun-0
49: /dev/disk/dsk8c DEC RZ1CF-CF (C)DEC phoey bus-1-targ-8-lun-0
50: /dev/disk/dsk9c DEC RZ1CB-CS (C)DEC jully bus-1-targ-9-lun-0
.
.
.
4. The following command enables you to display device information about
a particular component by specifying its device special file:
# /sbin/hwmgr view devices -dsf /dev/disk/cdrom0
HWID: DSF Name Mfg Model Location
--------------------------------------------------------
31: /dev/disk/cdrom0c DEC RRD47(C)DEC bus-0-targ-4-lun-0
5. The following example command displays the component hierarchy:
# /sbin/hwmgr view hierarchy
HWID: hardware hierarchy
------------------------------------
1: platform AlphaServer 800 5/500
2: cpu CPU0
4: bus pci0
5: scsi_adapter isp0
6: scsi_bus scsi0
18: disk bus-0-targ-0-lun-0 dsk0
19: disk bus-0-targ-4-lun-0 cdrom0
20: graphics_controller trio0
8: bus eisa0
9: serial_port tty00
10: serial_port tty01
11: parallel_port lp0
12: keyboard PCXAL
13: pointer PCXAS
14: fdi_controller fdi0
15: disk fdi0-unit-0 floppy0
16: network tu0
17: network tu1
6. The following example command displays the partial component
hierarchy. Use this command format to display information about
specific components:
# /sbin/hwmgr view hierarchy -id 45
HWID: hardware hierarchy
45: connection pci0slot15
70: ide_adapter ata0
71: scsi_bus scsi6
687: disk bus-6-targ-0-lun-0 cdrom53
72: scsi_bus scsi7
7. If a component has a status other than good, a status code appears
next to its entry in the command output, and the following code
definition string is appended to the header: (!) warning (X) critical
(-) inactive (see -status). For example, the following sequence of
commands simulates a CPU problem by forcing the CPU offline. The CPU
is flagged in the output as (X)critical:
# /sbin/hwmgr offline -id 700
hwmgr: CPU1 is now offline
# /sbin/hwmgr -view hier -id 700
HWID: hardware hierarchy (!)warning (X)critical (-)inactive (see -status)
---------------------------------------------------------------------------
700: X cpu CPU1
When the CPU comes back online the status code is cleared, as follows:
# /sbin/hwmgr online -id 700
hwmgr: CPU1 is now online
# /sbin/hwmgr -view hier -id 700
HWID: hardware hierarchy
---------------------------------------------------------------------------
700: cpu CPU1
If you see such status output, use the -status component command
option to view a status summary as described in hwmgr_ops(8) and refer
to the Managing Online Addition and Removal manual for more
information.
8. The following example displays the hwmgr command environment variable
settings:
# /sbin/hwmgr view env
HWMGR_DATA_FILE = "/etc/hwmgr/hwmgr.dat"
HWMGR_DEBUG = FALSE
HWMGR_HEXINTS = FALSE
HWMGR_NOWRAP = FALSE
HWMGR_VERBOSE = FALSE
9. The following (truncated) example displays all timestamps for all
hardware components registered on a small standalone system:
# /sbin/hwmgr view timestamps
HWID: Component Attribute Name Hostname Time occured
--------------------------------------------------------------------------------
1: COMPAQ AlphaSe registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
2: CPU0 registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
3: dmapi registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
4: scp registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
5: kevm registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
6: pci1 registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
7: pci1slot7 registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
9: pci1slot9 registration_time cymro.zk3. Mon Jul 22 10:23:20 2002
11: itpsa0 registration_time cymro.zk3. Mon Jul 22 10:23:24 2002
12: scsi0 registration_time cymro.zk3. Mon Jul 22 10:23:24 2002
13: pci2 registration_time cymro.zk3. Mon Jul 22 10:23:24 2002
10. The following example displays timestamps for a specific component, in
this case a hard disk:
# /sbin/hwmgr view timestamps -id 59
HWID: Component Attribute Name Hostname Time occured
---------------------------------------------------------------------------
59: dsk1 registration_time cariad.xxx. Thu Jun 20 16:00:28 2002
59: dsk1 last_event_time cariad.xxx. Thu Jun 20 16:00:33 2002
11. The following example displays all components that match a timestamp
value for a specific attribute:
# /sbin/hwmgr -view timestamps -a last_event_time="Thu Jun 20 16:00:33 2002"
#
HWID: Component Attribute Name Hostname Time occured
----------------------------------------------------------------------------
4: scp last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
5: kevm last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
36: tty00 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
3: dmapi last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
38: tty01 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
63: lp0 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
68: random last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
69: urandom last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
58: dsk0 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
59: dsk1 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
60: cdrom0 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
61: tape0 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
66: floppy0 last_event_time cariad.xxx Thu Jun 20 16:00:33 2002
12. The following example displays the transaction information for the
local host:
# /sbin/hwmgr view trans
hardware management transaction status
-----------------------------------------------------------
there is no active transaction on this system
the last transaction initiated from this system was:
transaction = general tx lock
proposal = 3835
sequence = 0
status = 0
the last transaction processed by this system was:
transaction = general tx lock
proposal = 3835
sequence = 0
status = 0
proposal last status success fail
---------------------------- ----------- ------- -------
Lock member/ 3847 0 85 0
Modify CDB/ 3838 0 4 0
Read CDB/ 3834 0 1 0
No operation/ 3835 0 89 0
Change name - lock/ 3836 0 0 0
Change name - commit/ 3837 0 0 0
Locate/ 3832 0 0 0
Scan/ 3801 0 0 0
Unconfigure - confirm/ 3933 0 0 0
Unconfigure - commit/ 3934 0 0 0
Delete - confirm/ 3925 0 0 0
Delete - commit/ 3926 0 0 0
Redirect - confirm/ 3928 0 0 0
Redirect - commit1/ 3929 0 0 0
Redirect - commit2/ 3930 0 0 0
Refresh - lock/ 3937 0 0 0
Change basename/ 3938 0 10 0
Unindict/ 3841 0 0 0
Indict/ 3840 0 0 0
FILES
See hwmgr(8) for more information.
SEE ALSO
Commands: dop(8), dsfmgr(8), hwmgr_show(8), hwmgr_get(8), hwmgr_ops(8),
sysman(8), sysman_station(8)
Files: olar_config(4).
Misc: olar_intro(5).
Hardware Management, Managing Online Addition and Removal
|
Index for
Section 8 |
|
|
Alphabetical
listing for H |
|
 |
Top of
page |
|