 |
Index for
Section 7 |
|
 |
Alphabetical
listing for V |
|
 |
Bottom of
page |
|
vme_univ_manual_setup(7)
NAME
vme_univ_manual_setup, sys_attrs_vba_univ - Describes how to set up
UNIVERSE II-based Alpha VME systems for use on the VMEbus, including how to
modify attributes of the vba_univ kernel subsystem
DESCRIPTION
VMEbus UNIVERSE II setup allows you to run the operating system on UNIVERSE
II-based Alpha VME systems. For information about installing the operating
system on these systems, see the Installation Guide.
For information about setting up VIP/VIC-based Alpha VME systems for use on
the VMEbus, see the sys_attrs_vba_vipvic(7) reference page.
See System Configuration Supplement: OEM Platforms for detailed information
about the use of the VMEbus on UNIVERSE II-based Alpha VME systems,
including the following topics:
· Configuring the vba_univ subsystem
· Configuring PCI-to-VME address spaces
· Configuring a special A24/A16 PCI-to-VME window
· Configuring VME-to-PCI address spaces
· Mapping UNIVERSE II CSRs to the VMEbus
· Mapping a location monitor window to the VMEbus
· Configuring VMEbus interrupts
· Using VMEbus software byte swapping
· Sharing memory between big endian and little endian processors
· Performing VMEbus slave block transfers
· Performing VMEbus master block transfers with local DMA
· Using the realtime interrupt-handling routine rt_post_callout
The defaults supplied for various VMEbus parameters are listed below. The
default values specified should provide proper VMEbus operation for most
applications. Be careful when modifying these values; not all adapters
support all fields.
Parameter Default Meaning
--------------------------------------------------------------------
VBA_ISR_Dispatch_Policy 1 Adapter interruupt dispatch
policy is to process all
interrupts for the current SPL
level (only)
VBA_Max_PCI_Sg_Size 0x20000000 Maximum PCI scatter/gather size
is 512 MB
VBA_Max_DMA_Wndw_Size 0x4000000 Maximum DMA window size is 64 MB
PCI_Coupled_Wndw_Tmr 0x2 Coupled Window Timer set to hold
VMEbus for 32 PCI clock cycles
after a coupled transaction
PCI_Max_Retry 0xF PCI maximum retries before
signaling error set to 960
(value*64)
PCI_Posted_Wrt_On_Cnt 0x0 PCI posted write transfer count
is 128 bytes
PCI_Aligned_Burst_Size 0x1 PCI aligned burst size is 64
bytes
VME_Br_Lev 0x3 Bus request level 3 for master
cycles
VME_Fair_Req 0x1 VMEbus request mode is fair (not
demand)
VME_Rel_Mode 0x1 Release mode is release on
request (ROR)
VME_Bus_To 0x6 VMEbus timeout period is 512
microseconds
VME_Arb_Mode 0x0 Arbitration mode is round robin
VME_Arb_To 0x1 VMEbus arbitration timeout
period is 16 microseconds
VME_Syscon 0x1 System controller VMEbus reset
is enabled
VME_Von_D64 0x4 VMEbus On counter for D64 MBLT:
hold bus tenure for 2048 bytes
VME_Voff_D64 0x9 VMEbus Off counter for D64 MBLT:
DMA interleave is 4 microseconds
VME_Von_D32 0x2 VMEbus On counter for D32 MBLT:
hold bus tenure for 512 bytes
VME_Voff_D32 0x9 VMEbus Off counter for D32 MBLT:
DMA interleave is 4 microseconds
--------------------------------------------------------------------
For the special A24/A16 PCI-to-VME (PCI slave) window:
--------------------------------------------------------------------
VME_A24_A16_Wnd_Ena 1 Special A24/A16 PCI-to-VME
window (64 MB) is enabled
VME_A24_A16_Wnd_WP_Ena 1 Write posting enabled to the
A24/A16 window
VME_A24_A16_Wnd_Dwdth 0xF A24/A16 window maximum data
width is D32 (all quadrants)
PCI_SLSI_Base 0 Stores A24/A16 (64 MB) window
base address (obtained from
firmware)
VME_A24_Size 0xFF0000 Stores the size of each A24
address space within the A24/A16
window; obtainable via sysconfig
-q, default is 16MB-64KB
VME_A16_Size 0x10000 Stores the size of each A16
address space within the A24/A16
window; obtainable via sysconfig
-q, default is 64KB
--------------------------------------------------------------------
For PCI-to-VME (PCI slave) windows 0 through 7:
--------------------------------------------------------------------
PCI_LSI_Base 0 Stores base address of the
contiguous PCI dense space
available for PCI-to-VME windows
(obtained from firmware)
PCI_Mem_Avail 0 Stores number of bytes allocated by
firmware for PCI-to-VME windows
PCI_Mem_Free 0 Stores number of bytes available
for further PCI-to-VME window
allocations
VME_Wnd0_Ena 1 Window 0 is enabled:
VME_Wnd0_VME_Address 0x80000000 VMEbus base address is 0x80000000
VME_Wnd0_Size 0x08000000 Size is 128 MB
VME_Wnd0_AM_Space 2 A32 space
VME_Wnd0_AM_Usr_Sprvsr 1 User mode
VME_Wnd0_AM_Data_Prg 1 Data access
VME_Wnd0_Dwdth 2 Maximum data width is D32
VME_Wnd0_WP_Ena 1 Write posting enabled
VME_Wnd0_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd1_Ena 1 Window 1 is enabled:
VME_Wnd1_VME_Address 0x80000000 VMEbus base address is 0x80000000
VME_Wnd1_Size 0x08000000 Size is 128 MB
VME_Wnd1_AM_Space 2 A32 space
VME_Wnd1_AM_Usr_Sprvsr 1 User mode
VME_Wnd1_AM_Data_Prg 2 Program access
VME_Wnd1_Dwdth 2 Maximum data width is D32
VME_Wnd1_WP_Ena 1 Write posting enabled
VME_Wnd1_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd2_Ena 1 Window 2 is enabled:
VME_Wnd2_VME_Address 0x80000000 VMEbus base address is 0x80000000
VME_Wnd2_Size 0x08000000 Size is 128 MB
VME_Wnd2_AM_Space 2 A32 space
VME_Wnd2_AM_Usr_Sprvsr 2 Supervisory mode
VME_Wnd2_AM_Data_Prg 1 Data access
VME_Wnd2_Dwdth 2 Maximum data width is D32
VME_Wnd2_WP_Ena 1 Write posting enabled
VME_Wnd2_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd3_Ena 1 Window 3 is enabled:
VME_Wnd3_VME_Address 0x80000000 VMEbus base address is 0x80000000
VME_Wnd3_Size 0x08000000 Size is 128 MB
VME_Wnd3_AM_Space 2 A32 space
VME_Wnd3_AM_Usr_Sprvsr 2 Supervisory mode
VME_Wnd3_AM_Data_Prg 2 Program access
VME_Wnd3_Dwdth 2 Maximum data width is D32
VME_Wnd3_WP_Ena 1 Write posting enabled
VME_Wnd3_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd4_Ena 1 Window 4 is enabled:
VME_Wnd4_VME_Address 0x00FF0000 VMEbus base address is 0xFF0000
VME_Wnd4_Size 0x00010000 Size is 64 KB
VME_Wnd4_AM_Space 1 A24 space
VME_Wnd4_AM_Usr_Sprvsr 1 User mode
VME_Wnd4_AM_Data_Prg 1 Data access
VME_Wnd4_Dwdth 2 Maximum data width is D32
VME_Wnd4_WP_Ena 1 Write posting enabled
VME_Wnd4_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd5_Ena 1 Window 5 is enabled:
VME_Wnd5_VME_Address 0x00FF0000 VMEbus base address is 0xFF0000
VME_Wnd5_Size 0x00010000 Size is 64 KB
VME_Wnd5_AM_Space 1 A24 space
VME_Wnd5_AM_Usr_Sprvsr 2 Supervisory mode
VME_Wnd5_AM_Data_Prg 1 Data access
VME_Wnd5_Dwdth 2 Maximum data width is D32
VME_Wnd5_WP_Ena 1 Write posting enabled
VME_Wnd5_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd6_Ena 0 Window 6 is disabled by default
VME_Wnd6_VME_Address 0x0
VME_Wnd6_Size 0x0
VME_Wnd6_AM_Space 0 A16 space
VME_Wnd6_AM_Usr_Sprvsr 1 User mode
VME_Wnd6_AM_Data_Prg 1 Data access
VME_Wnd6_Dwdth 2 Maximum data width is D32
VME_Wnd6_WP_Ena 1 Write posting enabled
VME_Wnd6_Cycle_Sel 0 VMEbus single cycles only
VME_Wnd7_Ena 0 Window 7 is disabled by default
VME_Wnd7_VME_Address 0x0
VME_Wnd7_Size 0x0
VME_Wnd7_AM_Space 0 A16 space
VME_Wnd7_AM_Usr_Sprvsr 1 User mode
VME_Wnd7_AM_Data_Prg 1 Data access
VME_Wnd7_Dwdth 2 Maximum data width is D32
VME_Wnd7_WP_Ena 1 Write posting enabled
VME_Wnd7_Cycle_Sel 0 VMEbus single cycles only
--------------------------------------------------------------------
For VME-to-PCI (VMEbus slave) windows 0 through 7:
--------------------------------------------------------------------
PCI_Wnd0_Ena 1 Window 0 is enabled:
PCI_Wnd0_VME_Address 0x00C00000 VMEbus base address is 0xC00000
PCI_Wnd0_Size 0x00400000 Size is 4 MB
PCI_Wnd0_AM_Space 1 A24 space
PCI_Wnd0_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd0_AM_Data_Prg 3 Both data and program access
PCI_Wnd0_WP_Ena 1 Write posting enabled
PCI_Wnd0_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd0_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd0_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd1_Ena 1 Window 1 is enabled:
PCI_Wnd1_VME_Address 0x08000000 VMEbus base address is 0x8000000
PCI_Wnd1_Size 0x08000000 Size is 128 MB
PCI_Wnd1_AM_Space 2 A32 space
PCI_Wnd1_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd1_AM_Data_Prg 3 Both data and program access
PCI_Wnd1_WP_Ena 1 Write posting enabled
PCI_Wnd1_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd1_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd1_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd2_Ena 0 Window 2 is disabled by default
PCI_Wnd2_VME_Address 0x0
PCI_Wnd2_Size 0x0
PCI_Wnd2_AM_Space 1 A24 space
PCI_Wnd2_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd2_AM_Data_Prg 3 Both data and program access
PCI_Wnd2_WP_Ena 1 Write posting enabled
PCI_Wnd2_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd2_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd2_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd3_Ena 0 Window 3 is disabled by default
PCI_Wnd3_VME_Address 0x0
PCI_Wnd3_Size 0x0
PCI_Wnd3_AM_Space 1 A24 space
PCI_Wnd3_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd3_AM_Data_Prg 3 Both data and program access
PCI_Wnd3_WP_Ena 1 Write posting enabled
PCI_Wnd3_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd3_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd3_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd4_Ena 0 Window 4 is disabled by default
PCI_Wnd4_VME_Address 0x0
PCI_Wnd4_Size 0x0
PCI_Wnd4_AM_Space 1 A24 space
PCI_Wnd4_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd4_AM_Data_Prg 3 Both data and program access
PCI_Wnd4_WP_Ena 1 Write posting enabled
PCI_Wnd4_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd4_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd4_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd5_Ena 0 Window 5 is disabled by default
PCI_Wnd5_VME_Address 0x0
PCI_Wnd5_Size 0x0
PCI_Wnd5_AM_Space 1 A24 space
PCI_Wnd5_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd5_AM_Data_Prg 3 Both data and program access
PCI_Wnd5_WP_Ena 1 Write posting enabled
PCI_Wnd5_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd5_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd5_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd6_Ena 0 Window 6 is disabled by default
PCI_Wnd6_VME_Address 0x0
PCI_Wnd6_Size 0x0
PCI_Wnd6_AM_Space 1 A24 space
PCI_Wnd6_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd6_AM_Data_Prg 3 Both data and program access
PCI_Wnd6_WP_Ena 1 Write posting enabled
PCI_Wnd6_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd6_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd6_PCI_Lock_Ena 0 Lock disabled (not modifiable)
PCI_Wnd7_Ena 0 Window 7 is disabled by default
PCI_Wnd7_VME_Address 0x0
PCI_Wnd7_Size 0x0
PCI_Wnd7_AM_Space 1 A24 space
PCI_Wnd7_AM_Usr_Sprvsr 3 Both user and supervisory mode
PCI_Wnd7_AM_Data_Prg 3 Both data and program access
PCI_Wnd7_WP_Ena 1 Write posting enabled
PCI_Wnd7_Pre_Rd_Ena 1 Prefetch reads enabled
PCI_Wnd7_PCI64_Ena 1 PCI64 transactions enabled
PCI_Wnd7_PCI_Lock_Ena 0 Lock disabled (not modifiable)
--------------------------------------------------------------------
For UNIVERSE II CSR and location monitor window mapping:
--------------------------------------------------------------------
CSR_Ena 1 UNIVERSE II CSR mapping enabled:
CSR_VME_Address 0xFFFF0000 VMEbus base address is 0xFFFF0000
CSR_AM_Space 2 A32 space
CSR_AM_Usr_Sprvsr 2 Supervisory mode
CSR_AM_Data_Prg 3 Both program and data access
LM_Ena 0 Location monitor mapping is
LM_VME_Address 0xFFFF1000 disabled by default
LM_AM_Space 2 A32 space
LM_AM_Usr_Sprvsr 2 Supervisory mode
LM_AM_Data_Prg 3 Both program and data access
The following VMEbus interrupt parameters provide initial defaults that are
later overwritten by system priority level (SPL) values supplied by the
platform. See the values listed in System Configuration Supplement: OEM
Platforms, or query the values at run time using the command sysconfig -q
vba_univ.
Parameter Default Meaning
--------------------------------------------------------------------
Irq0_SPL 4 VMEbus IRQ level to system SPL map
Irq1_SPL 4 VMEbus IRQ 1 to SPL SPLDEVHIGH
Irq2_SPL 4 VMEbus IRQ 2 to SPL SPLDEVHIGH
Irq3_SPL 4 VMEbus IRQ 3 to SPL SPLDEVHIGH
Irq4_SPL 4 VMEbus IRQ 4 to SPL SPLDEVHIGH
Irq5_SPL 4 VMEbus IRQ 5 to SPL SPLDEVHIGH
Irq6_SPL 4 VMEbus IRQ 6 to SPL SPLDEVHIGH
Irq7_SPL 4 VMEbus IRQ 7 to SPL SPLDEVHIGH
Adapt_Blk_SPL 4 Adapter resource blocking SPL
SPLDEVHIGH
SEE ALSO
Interfaces: sys_attrs_vme_vba(7), sys_attrs_vba_vipvic(7), sysconfigdb(8),
sys_attrs(5)
System Configuration Supplement: OEM Platforms, Device Driver Kit manual
Writing VMEbus Device Drivers
|
Index for
Section 7 |
|
|
Alphabetical
listing for V |
|
 |
Top of
page |
|