8    Creating and Modifying Secure Devices

The Information System Security Officer (ISSO) is traditionally responsible for assigning the devices that are included in the system's trusted computing base (TCB) and for defining the security characteristics of those devices. On a Tru64 UNIX system root access is required to assign devices. The trusted Tru64 UNIX system supports terminals as part of the TCB. This chapter describes how to define those devices in a secure system.

8.1    Defining Security Characteristics

The ISSO traditionally defines the security characteristics of all the terminals that are part of the system using the dxdevices program. To do this, the ISSO performs the following tasks:

• Creates and maintains device-specific information. The ISSO can override system defaults for an individual device, where appropriate, to grant additional rights or to impose additional restrictions. The ISSO can also lock a terminal to prevent use.

• Sets default control parameters for the devices that are included in the system's secure configuration. The system defaults for terminals are as follows:

  • Maximum number of unsuccessful login attempts is 10.

  • Login timeout as shipped is unset, which implicitly defaults to 0 which is treated as infinite.

  • Delay between unsuccessful login attempts is 2 seconds.

The ISSO is usually responsible for ensuring that all device assignments, whether they are set explicitly or by default, conform to a site's security requirements.

Before you create or modify a secure device, all of the typical device installation procedures required during ordinary system hardware and software installation must be completed. The special files for devices must exist in the /dev directory and have the appropriate permissions. The special files for terminals must be owned by root, have the group set to tty, and have the mode set to 0620.

You can verify that the installation has been completed with the ls command. The following example is typical:

# ls -lg /dev/tty*
 
crw----------  1  root  tty  0, 2 Aug 15 09:29 /dev/tty00
 
crw----------  1  root  tty  0, 3 Aug 15 09:29 /dev/tty01

8.1.1    Modifying, Adding, and Removing Devices with the dxdevices Program

Using the Devices dialog box, select the Modify/Create dialog box then the Select devices dialog box. To add or remove a device, first select or enter the device, then click on File to make the required changes. To modify a device, first select the device, then click on Modify to make the required changes. See the online help for dxdevices for more information.

8.1.2    Setting Default Values with the dxdevices Program

Using the Devices dialog box, select the Defaults dialog box. Set the system defaults for all of your terminals as required. A terminal uses these defaults unless specifically overridden by settings in the Modify Terminal dialog box. See the online help for dxdevices for more information.

8.2    Updating Security Databases

When you assign device defaults or device-specific parameters, the system updates the following security databases:

• The system defaults database, /etc/auth/system/default, contains the default values (for example, default control parameters) for all system devices.

• The device assignment database, /etc/auth/system/devassign, contains device-specific values for system devices.

• The terminal control database, /etc/auth/system/ttys.db, contains device-specific values for authentication (for example, the number of failed login attempts).

Each device to be used in your secure configuration must have an entry in the device assignment database. This database centralizes information about the security characteristics of all system devices. It includes the device pathname and type. By default a wildcard entry exists for terminals (but not X displays) in the /etc/auth/system/ttys.db and /etc/auth/system/devassign databases.

The X display entries shipped on the system have :t_login_timeout#0: entries in them, in case a site changes its system default login timeout. If wildcard X display entries are needed, they can be created as follows:

# echo \
 \'*\:*:t_devname=*\:*:t_login_timeout#0:t_xdisplay:chkent:\' \
                                       | /tcb/bin/edauth -s -dt
 
# echo \'*\:*:v_type=xdisplay:chkent:\' | /tcb/bin/edauth -s -dv