Loading Networks into UMBs with MS-DOS 5.0 (72016)



The information in this article applies to:

  • Microsoft MS-DOS operating system 5.0

This article was previously published under Q72016

SUMMARY

Network programs tend to use a lot of lower memory. If you have sufficient space for the programs in UMBs (upper memory blocks), you can achieve substantial memory savings. The following sections describe how to load some of the major networks into UMBs. If your network is not listed here, please contact your network vendor for information on how to load the network into a UMB.

NOTE: It is assumed in all of the following sections that you have read the "Running Programs in the Upper Memory Area" section in the version 5.0 "Microsoft MS-DOS User's Guide and Reference."

MORE INFORMATION

MS-NET Based Networks

Most MS-NET based redirectors are loaded with the NET command. Look in your AUTOEXEC.BAT file (or other file that you use to start the network) for a command similar to the following:
   net start <other>
				
where <other> is other text following START. Add the word LOADHIGH to the beginning of the line, as follows:
   loadhigh net start <other>
				
Reboot your computer and check to make sure that the network loads without problems. You can use the MEM command to see how much memory you now have available.

LAN Manager 1.x/2.x Based Redirectors

These redirectors are of two types: basic and enhanced. If you start the network with the command "NET START WORKSTATION," you are running the enhanced version. If you start the redirector with a command similar to "NET START RDR," you are running the basic version. Look in your AUTOEXEC.BAT file (or other file that you use to start the network) to see which command is used.

LAN Manager 1.x/2.x Basic Redirectors

These redirectors will often fit into a UMB. To load them high, add the word LOADHIGH before the NET START command:
   loadhigh net start <other>
				
Reboot your computer and check to make sure that the network loads without problems. You can use the MEM command to see how much memory you now have available.

LAN Manager 1.x/2.x Enhanced Redirectors

Best memory savings with LAN Manager enhanced redirectors (versions 2.0b and earlier) is achieved by instructing the network to use LIM memory.

  1. Use the RAM option on EMM386 to specify that both UMB and EMS memory be provided. For example, if the line to load EMM386.EXE is
          device=c:\dos\emm386.exe 1024
    						
    then change the line to the following:
          device=c:\dos\emm386.exe 1024 ram
    						
  2. Locate the LANMAN.INI file by typing the following at the MS-DOS prompt:

    c:
    cd \
    dir /s /b lanman.ini

    If more than one LANMAN.INI file is found, use the one that appears first in the PATH (use the PATH command to see the path).
  3. Edit the LANMAN.INI file. For example, if the file is in C:\LM.DOS, then use the following command:
          edit c:\lm.dos\lanman.ini
    						
    This command invokes the MS-DOS Editor.
  4. Use the SEARCH command to find the LIM option (ALT+S means hold down the ALT key while pressing S):

    ALT+S F

    A dialog box asking to "Find What" will be displayed. Type LIM and press ENTER.
  5. If the line has a semicolon (;) at the beginning, remove the semicolon. Ensure that the line now reads:
          lim = yes
    						

LAN Manager 2.0c

Microsoft LAN Manager version 2.0c is the first version of LAN Manager with the ability to load itself high with Microsoft MS-DOS version 5.0. The LAN Manager 2.0c redirector is loaded high automatically if there is enough room in the upper memory area (UMA). Other network services can be loaded high using the MS-DOS LOADHIGH (LH) command.

Loading Novell Networks into UMBs

When you start your network, specify LOADHIGH before the Novell startup command. For example, if you are using NET5.EXE to start Novell, add LOADHIGH before NET5.

REFERENCES

"Microsoft MS-DOS User's Guide and Reference," version 5.0

"Microsoft MS-DOS Getting Started," version 5.0

The Novell products included here are manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability.

Modification Type:MajorLast Reviewed:12/3/1999
Keywords:KB72016