Word is slow to start, print, or load documents (280821)
The information in this article applies to:
- Microsoft Office Word 2003
- Microsoft Word 2002
- Microsoft Word 2000
This article was previously published under Q280821
For a Microsoft Word 97 and an earlier version version of this article, see 123210.
Important This article contains information about how to modify the registry. Make sure to back up the registry before you modify it. Make sure that you know how to restore the registry if a problem occurs. For more information about how to back up, restore, and modify the registry, click the following article number to view the article in the Microsoft Knowledge Base: 256986 Description of the Microsoft Windows registry SYMPTOMS Microsoft Word starts very slowly, or other operations,
such as opening or printing documents, also are very slow. CAUSE This issue may occur if one of the following conditions is
true:
- Microsoft Windows is using a printer driver that is located
on a network print server, instead of a local printer driver on your hard disk.
When you use a remote printer driver, you may notice that it takes longer to
change your default printer setting, and sometimes Word may print documents
more slowly than you may expect.
- Word is installed on your computer, but Word was once
running from the network. When the computer is not connected to the network,
there is a long delay when you are opening documents.
- Fonts that are used in the Word document are damaged or
missing from the system, and Word cannot substitute other fonts in the
document.
When you start Word, it gathers information to use for document
formatting and printing operations. If the files, drivers, or fonts are
damaged, missing, or located on a remote server, Word can require more time to
connect to the server and gather the information that it needs. RESOLUTION To resolve this issue, use one of the following methods. Method 1: Reinstall the printer driver by using a local port Delete and reinstall your printer driver by using a local port.
To do this, follow these steps:
- Quit all Windows programs.
- Click Start, point to Settings, and then click Printers.
- Right-click your printer, and then click Delete on the shortcut menu. You receive the following message
Are you sure you want to delete the printer 'printer name'?
where 'printer name' is the name of
your installed default printer. - Click Yes.
- You may also receive an additional message when you delete
your printer driver:
Some files were used only for this printer and are no longer needed. Would you like to delete these files now?
If you receive the message, click Yes. - After Windows removes your installed default printer and
its associated files, reinstall the printer. To do this, use one of the
following procedures, depending on the version of Windows that you are using.
Microsoft Windows XP- Click Start, click Control Panel , click Printers and Other Hardware, and then click Printers and Faxes.
- Double-click Add Printer to start the Add Printer Wizard, and then click Next.
- Click Local printer, clear the "Automatically detect and install" check box, and then click Next.
- Click Create a new port, and then click Local Port in the Port type section.
- In the Port Name box, type the path to the printer in the following format where server is the name of the print server and printer is the name of the printer:
\\ server \ printer - Click Next, and then select a Windows 2000 or Windows XP driver for your printer.
- Click Next, and then follow the instructions to finish the wizard.
Microsoft Windows 2000- In the Printers dialog box (click Start, point to Settings, and then click Printers), double-click Add Printer. When the Printer Wizard appears, click Next.
- Click to select Local Printer, and then click Next.
- Click Create a new port, select Local Port in the Type box, and then click Next.
- Type the network share name for the printer in the Port Name box. For example, type \\Server name\My
printer, and then click OK.
- Click Next, select your printer manufacturer and model from the list, and
then follow the remaining steps in the wizard to reinstall your Windows printer
driver.
Click Next, and then use the disk that was provided by your printer manufacturer, and then
install it according to the installation instructions. For more information
about how to install the printer driver that was provided with your printer, please
contact your printer manufacturer.
For information about how to contact your printer manufacturer, click the appropriate article number in the following list to view the article in the Microsoft Knowledge Base: 65416 Hardware and software vendor contact information, A-K
60781 Hardware and software vendor contact information, L-P
60782 Hardware and software vendor contact information, Q-Z
For more information about troubleshooting steps that may help you solve printing problems, click the following article numbers to view the articles in the Microsoft Knowledge Base:
870968
How to troubleshoot general printing problems in Windows Server 2003 when you use Office products
870622 How to troubleshoot problems that you may experience when you try to print to a local printer by using Office programs in Windows XP
871146 How to troubleshoot general printing problems in Windows 2000 when you are using Office products
826864 How to troubleshoot damaged Word documents
Method 2: Reset the Word data key in the Windows RegistryWarning If you use Registry Editor incorrectly, you may cause serious
problems that may require you to reinstall your operating system. Microsoft
cannot guarantee that you can solve problems that result from using Registry
Editor incorrectly. Use Registry Editor at your own risk. If
Word is installed on your computer but the program was once running from the network and
there is a long delay when you open documents when you are not connected to the
network, try the following procedure. The Word Data key stores
information that is specific to the printer that is installed. To remove this
printer information from Word, rename or delete the Word Data key in the
Windows registry. When you restart Microsoft Word, Word recreates the Word Data
key automatically. Note After you rename or delete the Word data key, some settings in
Microsoft Word are reset to their default settings. To rename or
delete the Word data key in the Windows registry, follow these steps:
- Quit all Windows programs.
- Click Start and then click Run.
- In the Open box, type Regedit and then click OK.
- Open the following registry key that is for your version of Word:
Word 2003HKEY_CURRENT_USER\Software\Microsoft\Office\11.0\Word Word 2002 HKEY_CURRENT_USER\Software\Microsoft\Office\10.0\Word Word 2000 HKEY_CURRENT_USER\Software\Microsoft\Office\9.0\Word - Under the Word key, click the Data subkey.
- On the Edit menu, click Rename or Delete.
- Click Yes if the following message appears:
Are you sure you want to delete this key?
- On the Registry menu, click Exit.
- Start Word.
Method 3: Repair or replace damaged or missing fonts Damaged or missing fonts can cause the problem that is described in the
"Symptoms" section. To correct this problem, remove or reinstall the fonts, or do both,
in your version of Microsoft Windows.
For more information, click the following article numbers to view the articles in the Microsoft Knowledge Base:
234749
How to restore the Windows default fonts
314960 How to install or remove a font in Windows
306870 How to add
a new font to your Windows Me-based computer
131943 TrueType
font limits in Windows 95/98/Me
MORE INFORMATION
Microsoft provides third-party contact information to help you find technical
support. This contact information may change without notice. Microsoft does not
guarantee the accuracy of this third-party contact information.
Modification Type: | Major | Last Reviewed: | 3/23/2006 |
---|
Keywords: | kbPerformance kbopenfile kbstartprogram kbtshoot kbprb kbprint KB280821 |
---|
|