WD97: All Workstations Not Using Same Word Preference/Option Settings (196759)



The information in this article applies to:

  • Microsoft Word 97 for Windows

This article was previously published under Q196759

SYMPTOMS

After you install Word for Windows on a server, all or some of the workstations may not use the option or preference settings you selected during Setup. Instead, these workstations may all use the same set of defaults, such as the default font or Most Recently Used (MRU) list on the File menu.

CAUSE

This problem occurs if the Normal.dot file exists in the network server program directory, instead of in the user directory that you specified during the Workstation Setup.

Word (not Word Setup) creates the Normal.dot files in the server program directory. This occurs if the network administrator (or someone who has read, write, and create privileges in the Word program directory on the server) runs Word from the server installation before running a Workstation Setup to install Word on the workstation. Before you run the Workstation Setup, no references to the file locations exist in the Windows program directory, so when you quit Word the first time, it stores the Winword.opt and the Normal.dot files on the server in the directory where the Winword.exe program is located (the default location).

After the Normal.dot file exists on the server, Word uses these files every time it starts from any workstation, even if you have run a Workstation Setup and created a reference that points to another Normal.dot location. This happens because, as Word starts, it checks for these files in the directory where the Winword.exe file resides. If it finds Winword.opt or Normal.dot in this location, it uses those files and does not read your reference file to attempt to find them in another location.

NOTE: In some cases, it is desirable to have everyone use the same Normal.dot file and prevent any changes being made.

Infrequently, this problem also occurs if you ran the Workstation Setup at your workstation while you were running Windows from a different location (that is, from a location other than the one specified in your network logon script).

NOTE: Word Setup does not create the Normal.dot file. Word creates new versions of this file any time you run the program and the file is not located. Therefore, this is a network administration issue rather than a Word Setup issue.

RESOLUTION

Perform all three of the following steps to resolve this problem and restore each user's preference and option settings in Word:

  1. Quit all instances of Word running from the server. Rename or delete the Normal.dot files in the network server directory.
  2. Make sure the Word program directory on the network server and all files in that directory are flagged as read-only and shareable. You should not have write privileges in this server directory before you perform the Workstation Setup at the workstation.
  3. Make sure you run a Workstation installation of Word at every workstation where the user has administrative rights (that is, full access to the Word program directory on the server). This process references that point to the correct location for your user's Normal.dot file.

MORE INFORMATION

This section contains a description of the Normal.dot file and a discussion of the network installation of Word as it pertains to the problem addressed in this article.

Normal.dot

The default document template that stores macros, toolbars, menus, keystrokes, AutoText, and AutoCorrect entries. This file should be located in the user's Template directory and is created after the user makes a change to one of the items mentioned above. This file is not created by Setup. It is referenced in the Windows registry file.

Overview: Network Setup of Word

NOTE: This discussion assumes that you have a working knowledge of network operations and terminology. For network-specific information, see your network documentation.

To install Word so it runs from a network file server, go to a workstation and connect to the file server. Run the administrator's installation of Word (type "setup /a" at the command line). When Setup prompts you for the network directory for the main Word program, specify a path on the file server. Setup copies all the program files to this location.

IMPORTANT: DO NOT RUN WORD AT THIS POINT! If you do, the problems described at the beginning of this article may occur. Before you run Word, you must first perform the following two steps:

  1. Set the access privileges to read-only and shared for the server directories in which you installed Word. Refer to your MS-DOS or network operating system documentation for more information.
  2. Run the workstation installation of Word at each workstation. This registers the Word program with your local Windows installation and creates references to file locations. If you do not run a workstation installation before you run Word from the network server, Word runs, but some operations do not function correctly, such as the spelling checker, grammar checking, and object linking and embedding (OLE ).
NOTE: If you are running Windows from a network server, the first workstation installation of Word makes all the necessary Windows-level changes. This means you need all access privileges to the shared Windows program directory, and that directory must not be read-only.

Modification Type:MajorLast Reviewed:11/14/2000
Keywords:kbprb KB196759