BUG: Form Does Not Release After Being Changed to Modal (135612)


The information in this article applies to:

  • Microsoft Visual FoxPro for Windows 3.0
  • Microsoft Visual FoxPro for Windows 3.0b
  • Microsoft Visual FoxPro for Windows 5.0
  • Microsoft Visual FoxPro for Windows 5.0a
  • Microsoft Visual FoxPro for Windows 6.0
This article was previously published under Q135612

SYMPTOMS

When a form is changed from modeless to modal during run time, the form cannot be closed (terminated).

NOTE: In Visual FoxPro 6.0, the Close icon of the control box in the upper right corner of the form allows the form to close.

WORKAROUND

If the form needs to be Modal, set the WindowType to Modal at design time.

STATUS

Microsoft has confirmed this to be a problem in the Microsoft products listed at the beginning of this article. We are researching this problem and will post new information here in the Microsoft Knowledge Base as it becomes available.

MORE INFORMATION

When a form is changed to Modal at run time, it does not release when a Release ThisForm or ThisForm.Release is issued. The only way to close the form is to cancel the program.

Steps to Reproduce Problem

Example One:

  1. Create a form with the following command buttons:
    1. Command1 with Modal as the caption and the following code for Visual FoxPro 5.0: 
            ThisForm.Visible=.F.
      ThisForm.Show(1)
      ThisForm.Visible=.T.
    2. Command2 with Release as the caption and ThisForm.Release in the Click event procedure.

      NOTE: Ensure that the form's WindowType property is set to 0-Modeless.
  2. Run the form, and verify that the form is Modeless and that the Release button closes the form.
  3. Run the form, and click the Modal button. Verify that the form is modal. Click the Release button. The form will not close.
  4. Edit the form, and change the WindowType property to 1-Modal.
  5. Run the form, verify that the form is modal. Then click the Release button. The form should close.
Example Two: Setting the modal property programatically before the program executes causes the form to behave a little differently. Run the following program with the form's WindowType property set to 1. Click the Release button and verify that although the form is no longer visible, it has not closed. However, defining the form as modeless and then changing it to modal by pressing the Modal command button causes the form to remain on the screen. 
   ******* Start of Example *******

   frmModalForm=CREATEOBJECT("ModalForm")
   frmModalForm.Show
   READ EVENTS

   DEFINE CLASS ModalForm AS Form
     Top        = 9
     Left       = 26
     DoCreate   = .T.
     Caption    = "Modal Form Test"
     WindowType = 1 && Change WindowType to 0 to start the form as Modeless

     ADD OBJECT Command1 AS CommandButton WITH ;
          Top     = 145, ;
          Left    = 31, ;
          Height  = 29, ;
          Width   = 94, ;
          Caption = "Modal", ;
          Name    = "Command1"

     ADD OBJECT Command2 AS CommandButton WITH ;
          Top     = 145, ;
          Left    = 127, ;
          Height  = 29, ;
          Width   = 94, ;
          Caption = "Modeless", ;
          Name    = "Command2"

     ADD OBJECT Command3 AS CommandButton WITH ;
          Top     = 145, ;
          Left    = 225, ;
          Height  = 29, ;
          Width   = 94, ;
          Caption = "Release", ;
          Name    = "Command3"

     PROCEDURE Command1.Click
          ThisForm.Visible=.f.
          ThisForm.Show(1)
          ThisForm.Visible=.t.
     ENDPROC

     PROCEDURE Command2.Click
          ThisForm.Visible=.f.
          ThisForm.Show(0)
          ThisForm.Visible=.t.
     ENDPROC

     PROCEDURE Command3.Click
          ThisForm.Release
          CLEAR Events
     ENDPROC

   ENDDEFINE

   ******* End of Example *******
Modification Type:MajorLast Reviewed:5/7/2003
Keywords:kbBug KB135612
©2002 Microsoft Corporation. All rights reserved.