SNALU62 SNALU62_V401 SNA APPC/LU6.2 V4.0 for Tru64 UNIX ECO SUMMARY

TITLE: SNALU62 SNALU62_V401 SNA APPC/LU6.2 V4.0 for Tru64 UNIX ECO SUMMARY
 
Copyright (c) Compaq Computer Corporation 2000.  All rights reserved.

Modification Date:  19-APR-2000
Modification Type:  New Kit

PRODUCT:    DIGITAL SNA APPC/LU6.2 Programming Interface V4.0
              for Compaq Tru64 UNIX (formerly DIGITAL UNIX)

OP/SYS:     Compaq Tru64 UNIX [R]

SOURCE:     Compaq Computer Corporation

ECO INFORMATION:

     ECO Kit Name:  SNALU62_V401
     ECO Kits Superseded by This ECO Kit:  None
     ECO Kit Approximate Size:  10000 Blocks
     Kit Applies To:  SNA APPC/LU6.2 Programming Interface for 
                        Tru64 UNIX V4.0 
                      Compaq Tru64 UNIX V4.0D through V5.0 
     System/Cluster Reboot Necessary:  No
     Installation Rating:  Information not Available
     Kit Dependencies:

       The following remedial kit(s) must be installed BEFORE
       installation of this kit:

         None 

       In order to receive all the corrections listed in this
       kit, the following remedial kits should also be installed:

         None 

     INSTALLATION NOTE:  This is not an update kit and the current    
                         version of the LU6.2 Product must be deleted        
                         before installing this ECO.    


ECO KIT SUMMARY:

An ECO kit exists for SNA APPC/LU6.2 Programming Interface V4.0 on
Compaq Tru64 UNIX V4.0D - 5.0 (formerly DIGITAL UNIX).  The DEC SNA LU6.2 
Programming Interface Release Notes contain a complete explanation of this   
release.  This kit addresses the following problems: 

  o  TP ABENDed Due to a BID Race Condition

  o  Memory Leak in the LU6.2 Server

  o  Incorrect Return from snalu62_wait_for_completion()

  o  SNALU62_allocate() correlator_id parameter was not handled 
     correctly

  o  Allow Use of Access Name with Peer Server and Domain Gateway

  o  TCP/IP ports remain in CLOSE_WAIT state


INSTALLATION NOTES:

The ECO kit is distributed as a tar file containing the kit which can be
installed using the setld command.  The tar file should be unpacked to 
a suitable directory and then the setld command issued specifying that 
directory as the source  of the kit.

For example, if the tar file containing the kit has been copied to
/usr/tmp/snalu62401.tar:

# mkdir /usr/tmp/snalu62401
# cd /usr/tmp/snalu62401
# tar xf /usr/tmp/snalu62401.tar
# setld -l .

If the kit is delivered on tap11 then the commands would be:

# mkdir /usr/tmp/snalu62401
# cd /usr/tmp/snalu62401
# tar x
# setld -l .

Note that this is not an update kit, and the current version of the LU6.2     
Product must be deleted before installing this ECO.                          

Once the kit is installed, you should follow the instructions in the
installation guide's After installation section.


[R]  UNIX is a registered trademark in the United States and other
     countries licensed exclusively through X/Open Company Limited    

All trademarks are the property of their respective owners.

Colorado Site
Georgia Site

snalu62_v401.README
snalu62_v401.CHKSUM
snalu62_v401.CVRLET_TXT
snalu62_v401.tar
snalu62_v401.CVRLET_TXT